manualshive.com logo in svg

IDT 89HPEB383, Руководство пользователя

Поделиться
Скачать
IDT 89HPEB383 Скачать руководство пользователя страница 88

9. Error Handling > PCIe as Originating Interface

74

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

4.

Header is logged in the 

“PCIe Secondary Header Log 4 Register”

 and ERR_PTR is updated in the 

“PCIe Secondary Error Capabilities and Control Register”

 if R_MA Mask bit is clear in 

“PCIe 

Secondary Uncorrectable Error Mask Register”

 and ERR_PTR is not valid

5.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of R_MA bit in 

“PCIe Secondary Uncorrectable Error Severity Register”

 if R_MA Mask bit is clear in 

“PCIe 

Secondary Uncorrectable Error Mask Register”

 and either SERR_EN bit is set in 

“PCI Control and 

Status Register”

 or FTL_ERR_EN/NFTL_ERR_EN bit is set in 

“PCIe Device Control and Status 

Register”

6.

S_SERR bit is set in 

“PCI Control and Status Register”

 if an error message (Fatal/Non-Fatal) is 

generated and the SERR Enable bit is set in 

“PCI Control and Status Register”

7.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in 

“PCIe Device Control and Status Register”

9.2.6

Received Target-Abort On PCI Interface

This section describes the functionality of the PEB383 when a Target-Abort is received on the PCI 
Interface in response to posted, and non-posted transactions.

9.2.6.1

Target Abort On A Posted Transaction

When the PEB383 receives Target-Abort on the PCI Interface for posted requests, it takes the 
following actions:

1.

Drops the entire transaction

2.

R_TA bit is set in 

“PCI Secondary Status and I/O Limit and Base Register”

3.

R_TA bit is set in 

“PCIe Secondary Uncorrectable Error Status Register”

4.

Header is logged in the 

“PCIe Secondary Header Log 1 Register”

 and ERR_PTR is updated in the 

“PCIe Secondary Error Capabilities and Control Register”

 if R_TA Mask bit is clear in 

“PCIe 

Secondary Uncorrectable Error Mask Register”

 and ERR_PTR is not valid

5.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of R_TA bit in the 

“PCIe Secondary Uncorrectable Error Severity Register”

 if R_TA Mask bit is clear in the 

“PCIe 

Secondary Uncorrectable Error Mask Register”

 and either SERR_EN bit is set in the 

“PCI Control 

and Status Register”

 

or FTL_ERR_EN/NFTL_ERR_EN bit is set in the 

“PCIe Device Control and 

Status Register”

6.

S_SERR bit is set in 

“PCI Control and Status Register”

 if an error message (Fatal/Non-Fatal) is 

generated and the SERR_EN bit is set

7.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in 

“PCIe Device Control and Status Register”

9.2.6.2

Target-Abort On PCI Interface For Non-Posted Transaction

When the PEB383 receives a Target-Abort while forwarding a PCIe non-posted request to the PCI 
Interface, it takes the following actions:

1.

Returns a completion with Completer Abort status on the PCIe link

2.

R_TA bit is set in 

“PCI Secondary Status and I/O Limit and Base Register”

3.

R_TA bit is set in 

“PCIe Secondary Uncorrectable Error Status Register”

Содержание 89HPEB383









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды