IDT 89HPEB383 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 264

IDT 89HPEB383 Скачать руководство пользователя страница 140

14. Register Descriptions > Register Map

126

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

10

INT_DIS

Interrupt Disable

The PEB383 does not generate internal interrupts.

R

0

09

MFBBC

Fast Back-to-Back Enable

This field does not apply for PCIe bridges. It always reads 0.

R

0

08

SERR_EN

SERR# Enable

This bit enables reporting of non-fatal and fatal errors to the
Root Complex. In addition, this bit enables transmission by
the PCIe Interface of ERR_NONFATAL and ERR_FATAL
error messages on behalf of SERR# assertions detected on
the PCI Interface. Note that errors are reported if enabled
either through this bit or through the PCIe specific bits in the
Device Control register.

0 = Disable the reporting of bridge non-fatal errors and fatal

errors to the Root Complex.

1 = Enable the reporting of bridge non-fatal errors and fatal

errors to the Root Complex.

R/W

0

07

WAIT

IDSEL Stepping / Wait Cycle Control

This field does not apply for PCIe bridges. It always reads 0.

R

0

06

PERESP

Parity Error Response Enable

This bit controls the PEB383’s setting of the Master Data
Parity Error bit in the Status register in response to a
received poisoned TLP from PCIe.

0 = Disable the setting of the Master Data Parity Error bit.

1 = Enable the setting of the Master Data Parity Error bit.

R/W

0

05

VGAPS

VGA Palette Snoop

This field does not apply for PCIe bridges. It always reads 0.

R

0

04

MWI_EN

Memory Write Invalidate Enable

This bit controls the PEB383’s ability to translate PCIe
Memory Write Requests into PCI Memory Write and
Invalidate transactions.

0 = Do not translate Memory Write requests into PCI

Memory Write and Invalidate transactions.

1 = Promote Memory Write requests to PCI Memory Write

and Invalidate transactions.

R/W

0

03

SC

Special Cycles

This field does not apply for PCIe bridges. It always reads 0.

R

0

02

BM

Bus Master Enable

This field allows the PEB383 to perform bus-mastered
transactions on the PCIe link. The host or software driver
must ensure this bit is set to 1 for correct NTMA operation.

R/W

0

(Continued)

Bits

Name

Description

Type

Reset value

«
...
138
139
140
141
142
...
»

Содержание 89HPEB383









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды