Diagram References
Specification
Description
4
5
Installation
Detection Range
Anti-Masking Alarm
3
1
2
Enrollment
Masked:
PIR Triggered: (top)
Alarm:
MW Triggered:
(bo
�
om)
Fault:
+
UD24812N-D
Detec
�
on Method
Passive Infrared,Microwave
Detec
�
on Range
15m
Detection Angle
90° @ 180° adjustable
Detec
�
on Zones
92
Detectable Speed
0.3
〜
2m/s
Sensi
�
vity
Auto,Low
White Light Filter
10000lux
Pet Immunity
30Kg
Microwave Frequency
24GHz(24.15
〜
24.25GHz)
Digital Temperature Compensa
�
on
Tri-Signal Logic
An
�
-masking
Support
Support
Pattern mask included
Digital Processing
Tri-Signal Logic
Sealed Op
�
cs
Support
Tamper Protection
Front,Rear
Environment Temperature Indicator
Support
Signal Strength Indicator
Support
An
�
-Sway Analytics
Support
Power Switch
Power Up Enrolling
LED Indicator
Green(Top PIR), Red(Microwave),
Orange(Bottom PIR), Green+Orange(Mask),
Blue(Alarm)
Transmission Technology
Tri-X Wireless
Transmission Method
Two-Way RF Wireless
Transmission Frequency
868MHz
Transmission Security
AES-128 Encryption
RF Range
1.6Km
Frequency Hopping
Support
Enrolling Method
Power up,Remote ID,QR Code
Standard Battery Life
5 years in work status (being triggered 20
�
mes
per day)
Power Supply
Battery Powered
Battery Type
CR123A × 5
Typical Voltage
3V
Low Voltage Value
2.45±0.1V
Voltage Range
Fully charged(new) to 2.45±0.1V(battery)
Operating Temperature
-25 °C to 60 °C (-13 °F to 140 °F)
Storage Temperature
-25 °C to 60 °C (-13 °F to 140 °F)
Opera
�
ng Humidity
10% to 90%
IP Rate
IP65
Dimension(WxHxD)
75mm × 202mm × 73mm
Weight
600g
Mounting Height
0.8 to 1.2m
Moun
�
ng Method
Wall
Adaptable Coverage
Note: This product can only power the camera module as
its accessory.
EN 50131-2-4:2020
EN 50131-5-3:2017
EN 50131-1+A1+A2+A3
EC IV
，
SG 2
Cer
�fi
ed by KIWA
1. LED Indicator
2. Ver�cal Pole Mount
3. Screw Hole
4. Top/Bo�om Cover
5. Front Panel
6. PCBA
a. PIR Module (Top) b. PIR Module (Bo�om)
c. Tamper Switch d. Power Switch e. Microwave Module
f. Antenna g. PIR Angle
7. Rear Panel
I. Enrollment succeeded
Note: The front panel should be installed before
powering on successfully.
II. Check signal strength
I. Detector range
1. PIR Angle Se�ngs 2. PIR Distance Se�ngs
II. Masking seal
Product code :
0933393330939133
Helpdesk :
+27 (0) 87 159 7341
Wireless Outdoor Tri-Tech AM Detector
Содержание VX Pro 64 Series
