idronaut Ocean Seven 304Plus Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 79

background image

SECTION THREE

–

COMMANDS

IDRONAUT

–

Brugherio (MB)

OCEAN SEVEN 304

Plus

CTD

12-2015

29

Windows Personal Computer Preparation

The firmware is shipped together with the ITERM (IDRONAUT Terminal Emulation Programme).
The installation of ITERM is simple and does not require running any set-up.
Proceed as follows:



Copy the OS

304Plus

firmware upgrading package to a dedicated folder on the computer hard disk.



Unpack it using WINZIP or any other file uncompressing utility.



From the desktop and using the Windows resources, create a link on the desktop pointing to the
ITERM programme.



Run the ITERM programme. It starts with the correct communication parameters already set.



You are ready to switch ON the OS

304Plus

device.

Note



The ITERM port configuration is the following:



Communication speed

38400 bps



Data bit

8



Stop bit

1



Parity

None



Flow Control

None



The ITERM programme help contains the description of the programme main functions.

OS

304Plus

preparation

Connect the laboratory cable between the personal computer communication port and the OS

304Plus

and then switch on the OS304

Plus

. As soon as you switch the OS

304Plus

on, the start-up messages

must appear on the ITERM window.

Once the OS

304Plus

main menu appears, select the Service Menu and then select command 5. This

command allows the operator to access the “SETUP” using administrative rights. Once the command

is sent, the following message appears:

Access rights<<

Answer the request by typing “

ROOTACCESS

”. If the password is correctly entered and accepted

,

the menu appears again. From the shown service menu, select command 1

SETUP

! Go through the

parameters using the ENTER key until the request about the MAIN com port speed appears.

OCEAN SEVEN 304Plus - Setup
Configuration[191]-Status[177]-Calibration[309]{F8E5}
Warm-up timeout [s]:0 <
Number of rows between headers [1..255]:22 <
Main com. port BPS: 0)9k6,1)19k2,2)38k4,3)57k6,4)115k2:0 <

«
...
35
36
37
38
39
...
»

Содержание Ocean Seven 304Plus
















































































Отзывы:

Нет отзывов

Похожие инструкции для Ocean Seven 304Plus

Two-Knife Booklet Trimmer-A1

Бренд: Canon Страницы: 32

Perfect Binder-C1

Бренд: Oce Страницы: 82

Бренд: Klarstein Страницы: 96

Formula F732 WIZARD

Бренд: Datalogic Страницы: 2

Бренд: HAI Страницы: 2

Бренд: Hahnel Страницы: 176

Бренд: IFO Страницы: 12

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Patton electronics Страницы: 12

Бренд: Q'STRAINT Страницы: 10

Бренд: RADEMACHER Страницы: 48

Бренд: rako Страницы: 7

Бренд: Saft Страницы: 6

Бренд: BAFANG Страницы: 9

efector 190 DTE820

Бренд: IFM Electronic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды