background image

12

DOC No: 8540 REV E

13

DOC No: 8540 REV E

The two fault signals provide diagnostic feedback to the user’s control 
system. These use the common ground to provide HI or LOW signals. 
When both Fault Signals indicate HI, the EagleDrive is operating normally 
(no faults detected). Signals are driven with 5.6kohm pull-up resistors to the 
internal 5V and should be monitored with a high impedance device (R

load

 > 

100kohms).

Caution:

  Do not short Fault Signals to ground or EagleDrive will not 

operate properly.

Fault Signal Out

Fault 
Signal 1

Lead 8
Brown

Fault
Signal 2

Lead 7
Blue

Fault 
Description

Drive 
Condition

Reason for 
Fault

Remedy

0

0

Under 
Voltage

Disabled

Voltage 
supply less 
than 8.5V

Ensure proper supply voltage, 
check power and ground 
connections

0

0

Over 
Temperature

Operating

Internal 
component 
temperature 
greater than 
170º C

Reduce load or increase 
cooling

0

0

Logic Fault

Disabled

Drive cannot 
locate the 
magnets 
inside the 
pump

Ensure pump is correctly 
attached to EagleDrive

1

0

Internal Short

Disabled

Drive 
components 
have failed

Reset EagleDrive by 
disconnecting and restoring 
power supply connection, 
if problem persists, contact 
Micropump for a replacement.

0

1

Low Load 
Current

Operating

Drive 
components 
have failed

Reset EagleDrive by 
disconnecting and restoring 
power supply connection, 
if problem persists, contact 
Micropump for a replacement.

1

1

None

Operating

No Fault

CAUTION

1

2

3

4

5
7

8

9

6

MODEL DEMSE

1

2

3

4

5
7

8

9

6

MODEL DEELE

LEAD

FUNCTION

GRAY CABLE 

WIRES

BLACK CABLE 

WIRES

1

POWER

RED

RED

+12 to +36 VDC, Class 2 
(SELV), Reverse-polarity 

protected

2

SPEED PWM IN

VIOLET

YELLOW

Ground if not used

3

GROUND

BLACK

BLACK

Common isolated from motor 

housing

4

FAULT OUT

BROWN

BROWN

Fault Signal 1

5

FWD/REV

ORANGE

ORANGE

Forward (

fl

 oat and insulate), 

Reverse (ground)

6

FAULT OUT

BLUE

BLUE

Fault Signal 2

7

TACH OUT

GREEN

GREEN

5 V square wave-2 pulses per 

revolution

8

SPEED 0-5 IN

YELLOW

WHITE

Control signal in, 0-5 VDC

9

SHIELD

BARE

BARE

Connected to Common

EagleDrive Lead Wire Assignments

Содержание MICROPUMP EagleDrive DEELE













Отзывы: