Idex MICROPUMP 668-400-2 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 33

Idex MICROPUMP 668-400-2 Скачать руководство пользователя страница 23

MICROPUMP, INC.

A Unit of IDEX Corporation

PO Box 8975, Vancouver, WA 98668-8975 • Phone: 360/253-2008 • Fax: 360/253-8294

MICROPUMP

LIMITED

A Subsidiary of Micropump, Inc.

2 Howard Road, Eaton Socon, St.

Neots, Cambridgeshire, PE 19 8ET England, • Phone: 011-44-1480-356600 • Fax: 011-44-

1480-

356300

Page 23 of 33

6.2.2.2 Insert bushing into hole in body or pump base assembly and seat with

bushing insertion tool. Seat bushing to 0.15 inch (0.038 cm) below body
or pump base surface as applicable.

6.3 Motor and Drive Housing Assembly with Pressure Switch

6.3.1 Repair of the motor and drive housing assembly with pressure switch is limited

to replacing either the magnet assembly or the entire assembly, including the
pressure switch. Replacement should be made for any motor winding that does
not pass the motor winding test (refer to Testing and Troubleshooting). Also
replace if rotor shaft is bent.

7. Assembly

7.1 Tools & materials

7.1.1 The following tools and materials are required to assemble the Model 668-400-2.

Note: Equivalent substitutes may be used.

7.1.1.1 One (1) each 3/32 inch (0.238 cm) hex key.

7.1.1.2 One (1) each flat blade screwdriver, 3/16 inch (0.476 cm).

7.1.1.3 Dow Corning high-vacuum grease.

7.2 Assembly of Pump Assembly (-1). (Refer to Figure 2 in IPL.)

CAUTION: DO ALL WORK ON CLEAN SURFACE.

7.2.1 Install screen (33) in body assembly (2). Lightly lubricate O-ring (34) with

specified grease and place into groove in cap (32). Thread cap into body
assembly.

7.2.2 Insert piston (22) in pressure regulator hole in body assembly (2). Lightly

lubricate O-ring (21) with specified grease and place on lip inside pressure
regulator hole. Install retainer (20), spring (19), and retainer (18).

7.2.3 Install spring (29), shim or shims (28), plate (27), ball (26), and sleeve (25) in

remaining hole in body assembly (2). Then add spring (24), adapter (23) with
O-ring (30) and (31) at each end of adapter.

7.2.4 Place adjuster assembly (15) with adjusting screw (16) and nut (17) over

assemblies installed in Steps 7.2.2 and 7.2.3. Attach to body assembly (2) with
two screws (14).

«
...
21
22
23
24
25
...
»

Содержание MICROPUMP 668-400-2


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды