IDEAL Classic SE12 FF Скачать руководство пользователя

Страница: 21 / 44

Classic SE

Installation & Servicing

INSTALLATION

SIDE FLUE OUTLET

The boiler is supplied for rear
outlet installation. Remove
the blanking plate from the
direction required and use
this to blank off the rear outlet.

Lift the boiler onto the wall
mounting plate hooks as
shown.

Do not use the burner/
controls for lifting.

Fit the M8 screw, washer and
rectangular plate to retain the
boiler.

Note.

Before fully tightening the

M8 screw check the boiler
alignment using a spirit level and
adjust as necessary with the
jacking screw.

29 WALL MOUNTING PLATE

Fix the mounting plate to the wall with the No.14 x 50mm
wood screws.

If downward routing of pipes is required then the
downward routing pipe brackets and M8 spacer
(supplied in the Downward Piping Kit) should be fitted to
the wall mounting plate now.

Fit the bottom 2 screws to secure the bracket(s) to the
wall, through the wall mounting plate.

Check with a spirit level that the plate is vertical.

Notes

Have ready to hand the M8 screw, washer and rectangular plate supplied in the hardware pack.

For downward routing of pipes the M5 spacer (supplied in the Downward Piping Kit) should now be
fitted to the back of the boiler.

28 FITTING THE SIDE OUTLET PLATES

30 MOUNTING THE BOILER

Note.

If the boiler is fitted closer than 25mm to the side wall

the side outlet plate must be fitted now.

Split the side outlet plate into 2 down the split line.

Fit the 2 halves of the side outlet plate to the wall,
ensuring they are behind the boiler sealing ring.

200544-5.pmd

20/02/2008, 13:26

Содержание Classic SE12 FF













































Результаты поиска

Содержание Classic SE12 FF

Отзывы:

Похожие инструкции для Classic SE12 FF

Бренды по названию

Популярные бренды

IDEAL Classic SE12 FF, Руководство по установке и обслуживанию

Результаты поиска

Содержание Classic SE12 FF

Отзывы:

Похожие инструкции для Classic SE12 FF

Бренды по названию

Популярные бренды