IDEAL British Gas 100 RD2 Скачать руководство пользователя | Manualshive

Страница: 13 / 44

background image

13

British Gas 100 & 125 RD2 -

Installation & Servicing

INSTALLATION

9

BOILER CASING REMOVAL

The boiler is supplied fully assembled in
Pack A, together with a standard flue
assembly for lengths up to 600mm (23 1/2")
rear or side flue outlet in Pack B.
Unpack and check the contents.

8

UNPACKING

complete boiler

assembly

PACK 'A' CONTENTS

z

Complete boiler assembly

z

The Boiler Hardware Pack (listed
separately)

z

The Flue Hardware Pack (listed
separately)

z

These Installation/Servicing
Instructions

z

User's Instructions.

z

Template

To install the boiler the casing MUST be removed.

1.

Undo the 2 screws and lift off the lower front panel.

2.

Remove the 2 screws and lift off the grille assembly.

3.

Release the 'Burner On' neon from the rear of the
control panel.

4.

Release the wiring harness leads from the edge clips
on the RH side panel.

5.

Remove the 2 screws securing the control panel and
pull down to release the tabs from under the top
panel.

BOILER HARDWARE PACK

z

1" BSP plugs - 3 off.

z

Distributor tube - 1 off.

z

28mm x 1"BSP male straight
adapter compression fitting - 3 off.
For connection to the boiler
PUMPED & GRAVITY flow /return
tappings.

z

Flow sensor pocket -1 off.

z

Return sensor pocket kit
comprising:
Hexagon bush - 1 off.
Sensor pocket - 1 off.
'O' ring - 1 off.
Heyco bush - 1 off.
M5 x 10mm Pozi screw - 3 off.
Washers - 3 off.

z

O/heat thermostat pocket - 1off

z

1/2" square bar - 1 off.

z

Cable tie - 4 off.

z

Control thermostat knob - 1 off.

z

M3 x 6mm Pozi pan screw- 1 off.

z

Self tapping screw - 2 off.

z

British Gas Logo- 1 off.

z

Scottish Gas Logo - 1 off.

FLUE PACK. Pack B Contents

z

Duct cutting support - 2 off (cardboard )

z

Terminal wall plate - 1 off.

z

Terminal grille assy. - 1 off.

z

Polyurethane foam seal 400 lg. - 1 off.

z

No. 8 x 8 lg. Pozi pan hd. screws - 3 off.

FLUE HARDWARE PACK

Side outlet plate

z

Flue extension tube (rear).

z

Flue extension tube (side).

z

Flue extension tube (top).

z

Elbow .

z

Sealing ring.

z

M5 wing nuts - 3 off.

z

Side outlet plate.

z

No. 10 x 2" lg. Rd Hd.wood
screws - 4 off.

z

Wall plugs - 4 off.

Flue terminal

Terminal wall plate

INST

ALLA

TION

«
...
11
12
13
14
15
...
»

Содержание British Gas 100 RD2













































Отзывы:

Нет отзывов

Похожие инструкции для British Gas 100 RD2

Бренд: Quantec Страницы: 44

Aerco Modulex EXT Series

Бренд: Watts Страницы: 144

Vitodens 100-W B1HA

Бренд: Viessmann Страницы: 48

Henrad WH 100 FF

Бренд: IDEAL Страницы: 4

Бренд: IDEAL Страницы: 52

Pellematic PE 12-20

Бренд: MAINE ENERGY SYSTEMS Страницы: 34

Бренд: Warmhaus Страницы: 40

Бренд: NTI Страницы: 4

Бренд: Hendi Страницы: 68

Flexible Water Tube Boilers

Бренд: Bryan Boilers Страницы: 8

Бренд: Climit Страницы: 116

Бренд: Vapac Страницы: 31

Modulex EXT 440

Бренд: Automatic Heating Страницы: 55

Бренд: Potterton Страницы: 32

Бренд: ACV Страницы: 64

VITOCONTROL-S, WB2B

Бренд: Viessmann Страницы: 124

Vitogas 050 Rs Series

Бренд: Viessmann Страницы: 32

Бренд: HDG Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды