Ideal Vacuum Habanero P1012726 Скачать руководство пользователя

Страница: 14 / 19

[email protected] | www.idealvac.com

HRCF-08122022 - V 1.1

4.1 AVAILABLE REPLACEMENT WINDOWS

4. WINDOW REPLACEMENT

Two 1” diameter, uncoated, wedged fused silica windows are included standard with the Habanero

furnace. Window replacements may be required if the optics become degraded over time due to

elevated temperatures. If focusing or other special considerations are required for an application,

the researcher can substitute windows with their own optics. The furnace uses 1 inch diameter

windows up to a maximum thickness of 8 mm. The windows may be removed entirely, which

results in reduced heating performance and temperature uniformity. Below, Table 4 lists our

available replacement windows. All are 1” diameter (25.4 mm), 5 mm (.197 in.) thick, 0.5

wedge,

and have high surface flatness to prevent beam distortion.

Part #

Material

Maximum

Temperature

Transmission

Range

Reflection Loss

P1012275

N-BK7

619°C

350-2000 nm

8.1% @ 587.5618 nm

P1012276

Fused Silica*

1600°C

185-2100 nm

6.8% @ 588 nm

P1012277

Sapphire

1134°C

150-5000 nm

14% @ 1060 nm

P1012278

Calcium

Fluoride

600°C (Humid)

1000°C (Humid)

130-10000 nm

5.4% @ 5000 nm

* Included standard with furnace.

Table 3 - Available replacement windows

Содержание Habanero P1012726




















Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды

Ideal Vacuum Habanero P1012726, Руководство пользователя

Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды