Ideal Heating GB24 Скачать руководство пользователя

Страница: 13 / 44

SECTION 2 - INSTALLATION

Note.

A 5º or 14º pitched roof plate (not supplied) is required before proceeding with the

installation of this kit.

This kit is suitable for both 5º and 14º pitched roof terminations, using a concentric

flue to run vertically from the top of the boiler and terminating above roof level.

Connection to the top of the boiler is made using a vertical connector (supplied in

the kit - RSF346).

WEATHER PROOFING

Where the flue passes through the roof line an adequate seal must be made. This

is achieved by using a suitable sealant.

ACCESSORIES

Flue Duct Extension Kits are available for flue lengths extending beyond 1m. These

packs contain 1m extension ducts and may be cut to the desired length. If 90º

elbows are used (RSF315) they will reduce the overall height by 1m per elbow.

2.8 FITTING THE OPTIONAL ROOF FLUE KIT RSF345 (OPTIONAL) - Flat or Pitched-

Terminal Position

Minimum Dimension

Directly below an opening,

air brick, windows, etc.

300 mm

Below plastic / painted gutters

300 mm

Painted surface

300 mm

Below eaves or balcony

500 mm

Below velux windows

2000mm

Above or side of velux windows

600mm

2.9 ASSEMBLING THE ROOF FLUE KIT

Position the roof plate (supplied separately) over the hole cut in the roof and insert flue

terminal from the roof end.

Ensure that if the length needs to be adjusted to allow an additional 30mm added

to the outer air tube length and 14mm added to the inner flue length. This allows

correct engagement into the vertical connector.

Note. Ensure a square cut. remove all burrs and sharp edges.

Fit the vertical connector (supplied in the kit) and secure the vertical connector by

applying downward pressure on the connector.

Position the clamp on the top face of the flue manifold and push it horizontally

backwards. Locate both clamp lugs into the flue manifold and secure to the flue

manifold clamp with the M5 retaining screw.

“Push” assembly A into vertical connector.

Notes.

Ensure turret sample points are servicable and all caps and plugs are fitted.

Ensure condensate siphon/trap is filled with water.

Finally ensure the roof plate is correctly sealed to the roof.

Assembly A

Vertical

connector

5º & 14º

MAX LENGTH:

7.5m**

**minus any

90º bends

MIN LENGTH:

0.950m

BOILER

Flue Terminal

RSF050

14º

RSF051

5º

ASSEMBLY A

Содержание GB24













































Результаты поиска

Содержание GB24

Отзывы:

Похожие инструкции для GB24

Бренды по названию

Популярные бренды

Ideal Heating GB24, Технические инструкции

Результаты поиска

Содержание GB24

Отзывы:

Похожие инструкции для GB24

Бренды по названию

Популярные бренды