Ideal Heating ECOMOD AHP60 26 kW Скачать руководство пользователя страница 57

Страница: 57 / 74

01-07-2022

57 / 74

AHP60

26/32 kW -

Installation, Use and Maintenance

Error code

Error designation

Probable causes

Solution

E861

- Overcurrent during speed

up
- Overcurrent at permanent

speed regime

- Outlet short circuit (ground

connection)
- Blocked rotor, or heavy load

Unplug compressor cabling

and check each driver line.

Launch card operation without

compressor

Overcurrent during slow-

down
POE protection detects

overcurrent

Compressor cabling phases

are inverted

Check the compressor cabling

line by line and ground fault

- Program on current during

speed-up
- Program on current in

permanent regime
- Program on current during

slow-down

Compressor load too heavy

Check differential pressure

during start driving.
Check externant fan.

Rotor is blocked, or magnet is

damaged

Unplug compressor cabling and

launch electronic card operation

without the compressor

Compressor cabling phases

are inverted

Check the cabling between the

compressor and the card

E871

Heat sink overheat

- IPM module (100-125°C)
- PCF module (>95°C)
- housing (>75°C)

Ambient temperature too high

Check clogging in cooling

phase (fan or sink)

Presence of heat source

nearby

Reduce ambient temperature

around the driver.

Cooling air flow is unsufficient

Increase the housing air flow

E881

DC bus low voltage
Serie 220V: 180 VDC
Serie 380V: 310 VCC

Power supply voltage variations

are too high

Check supply voltage

Temporary current cut occurred
Supply terminals are screws

are weak

Check the terminals

connections strength.

PFC converter failure

Check precharge contactor

Over voltage of DC bus
- Serie 220V: 400VDC
- Serie 380V: 800VCC

Power supply voltage too high Check supply voltage.
PFC converter failure

Check the bus condensator

voltage and replace PFC card

if the failure is continuous

E911

Output current exceeded the

driver overcharge capacity

Charge compressor is too

heavy.

Reduce compressor load.

Driver capacity is too low.

Increase appropriately the

driver capacity.

E921

PFC converter on current

(only F008i-2PHB)

Input short circuit

Unplug the power supply and

check the short circuit between

the PFC phases input

Short circuit or leakage on

reactor

Check the reactor's insulation

and inductance

Input voltage sensor cabling

fault

Check the input voltage sensor

cabling.

E941

PFC converter fault
(only F008i-PHB)

Cabling input phase sequence

is negative, or pashe loss

Check the cabling input voltage

level

Bad contact on PFC control

signals connector

Check PFC control signals

cabling

E951

Error on heater temperature

sensor

Temperature sensor's cable is

broken

Check the heater temperature

and the sensor cabling

Temperature sensor may be

damaged

Restart the driver, replace the

sensor if the error remains

Housing temperature sensor

error

The sensor may be damaged

Restart the driver, replace the

mothercard if the default is

continuous.

Содержание ECOMOD AHP60 26 kW











































































Результаты поиска

Содержание ECOMOD AHP60 26 kW

Отзывы:

Похожие инструкции для ECOMOD AHP60 26 kW

Бренды по названию

Популярные бренды

Ideal Heating ECOMOD AHP60 26 kW, Установка и обслуживание

Результаты поиска

Содержание ECOMOD AHP60 26 kW

Отзывы:

Похожие инструкции для ECOMOD AHP60 26 kW

Бренды по названию

Популярные бренды