ideal commercial Evomax 30 Скачать руководство пользователя страница 40

Страница: 40 / 66

INSTALLATION

EVOMAX

Installation & Servicing

INST

ALLA

TION

INST

ALLA

TION

INST

ALLA

TION

DISABLING THE ANTI-LEGIONELLA FUNCTION

Installer Mode

Normal Operation

Set Flow Temp’
Set DHW Temp’

Note that the Anti-Legionella Temperature Function is only

operational if a Domestic Hot Water Thermistor has been connected.

Care should be taken in disabling this function as an unsafe condition

could result.
Press SELECT and then hold + and - down together for more than

5s, the following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
Anti-Legion Temp’

Anti-Legion Enable

BUS Address
Flame/LPG Relay

Press SELECT and the following screen will be displayed

Anti-Legion Enable

Off

Press + and - to change to required setting then press ENTER to store

Rotate the KNOB clockwise until Normal Operation is highlighted again

and press SELECT to return to normal operation

CHANGING THE VOLT FREE BURNER ON RELAY TO OPERATE
AS AN LPG RELAY FOR BELOW GROUND LEVEL LPG
APPLICATIONS

Installer Mode

Normal Operation

Set Flow Temp’
Set DHW Temp’

If LPG is to be used in an application below ground level then an

additional valve is required to control the LPG input to the boiler

This valve should be wired from the Volt Free Burner on Relay and

enabled as follows
Press SELECT and then hold + and - down together for more than

5s, the following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
BUS Address

Flame/LPG Relay

Normal Operation

Press SELECT and the following screen will be displayed

Flame/LPG Relay

Flame On

LPG Gas Valve

Press + and - to change to the required setting and then press

ENTER to store

Rotate the KNOB clockwise until Normal Operation is highlighted

again and press SELECT to return to normal operation

40 EVOMAX USER INTERFACE - ADVANCED OPERATING INSTRUCTIONS CONTINUED....

REVERTING TO FACTORY SETTINGS

Installer Mode

Normal Operation

Set Flow Temp’
Set DHW Temp’

Press SELECT, hold + and - together for more than 5s, the

following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
DHW Sensor

Factory Settings

Anti-Legion Temp’
Anti-Legion Enable

Press SELECT and the following screen will be displayed

Factory Settings

Reset?

Press ENTER and a screen similar to the following will be displayed

Factory Settings
Are you sure?
Press Enter to Reset
Press Select not to
Reset

Press ENTER and a screen similar to the following will be displayed

Factory Settings

Reset?

Press Select then Rotate the KNOB clockwise until Normal Operation

is highlighted again and press SELECT to return to normal operation

CHANGING THE ANTI-LEGIONELLA TEMPERATURE

Installer Mode

Normal Operation

Set Flow Temp’
Set DHW Temp’

Note Anti-Legionella Temp. Function is only operational if a DHW

Thermistor has been connected

Care should be taken reducing this temp. as unsafe condition could result
Press SELECT and then hold + and - down together for more than 5s,

the following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
Factory Settings

Anti-Legion Temp’

Anti-Legion Enable
BUS Address

Press SELECT and the following screen will be displayed

Anti-Legion Temp’

70°C

Press + and - to change to required setting, press ENTER to store

Rotate the KNOB clockwise until Normal Operation is highlighted again

and press SELECT to return to normal operation

Содержание Evomax 30



































































Результаты поиска

Содержание Evomax 30

Отзывы:

Бренды по названию

Популярные бренды

ideal commercial Evomax 30, Установка и обслуживание

Результаты поиска

Содержание Evomax 30

Отзывы:

Бренды по названию

Популярные бренды