Ideal Boilers Mexico Super RS 3/100P Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 40

background image

19

Mexico Super RS 3/60P - 3/100P -

Installation

INSTALLATION

25 INITIAL LIGHTING

1.

Turn the gas service cock to OFF and undo the union
nut.

2.

Remove the 4 wing nuts and withdraw the burner and
controls assembly, complete, from the boiler.

3.

Invert the burner assembly and reconnect to the gas
service cock.

4.

Turn the gas service cock to ON.

5.

Light the pilot burner. Refer to Frame 25.

6.

Test for gas soundness around the pilot burner
connection, using leak detection fluid.

7.

Turn the gas service cock to OFF and return the
burner and controls assembly to the normal working
position.

INST

ALLA

TION

26 PILOT BURNER CONNECTION GAS SOUNDNESS

LEGEND

A

Gas control knob

B

Burner pressure test point

C

Main burner pressure
adjuster

D

Inlet pressure test point

E

Gas service cock

F

Sightglass

G

Piezo unit ignition

H

Boiler thermostat knob

J

Overheat thermostat reset
button (optional)

1.

Connect the gas valve electrical leads and refit the cover.

2.

Check that the gas service cock (E) is ON and that the boiler
thermostat control knob (H) is OFF.

3.

Loosen the screw in the burner pressure test point (B) and
connect a gas pressure gauge via a flexible tube.

4.

Turn the gas control knob (A) CLOCKWISE until resistance
is felt and then release it.

5.

Push in and retain fully depressed the gas control knob (A).
Press and release the piezo unit button (G) repeatedly until
the pilot is seen to light through the sightglass (F).

6.

Hold the gas control knob (A) depressed for 15 seconds
after the pilot burner has ignited, then release.
If the pilot burner fails to remain alight at this stage, repeat
the procedure detailed above but wait longer than 15
seconds before releasing the gas control knob (A).

7.

Check the appearance of the pilot flame to ensure that it
envelops the tip of the thermocouple and is approximately
25mm (1") long. The pilot flame is factory set and no
adjustment is possible.

8.

Switch the boiler thermostat control knob (H ) to position 6
and check that the burner cross-lights smoothly from the
pilot flame.

9.

Test for gas soundness around the boiler gas component
joints, using leak detection fluid.

10.

Operate the boiler for 10 minutes to stabilise the burner
temperature. The boiler is pre-set at the factory to its
maximum nominal rating

11

. Turn the boiler thermostat knob (H) to OFF.

12.

Remove the pressure gauge and tube. Retighten the screw
in the pressure test point, ensuring that a gas-tight seal is
made.

RS 3/60P Burner / controls assembly shown

«
...
17
18
19
20
21
...
»

Содержание Mexico Super RS 3/100P









































Отзывы:

Нет отзывов

Похожие инструкции для Mexico Super RS 3/100P

Gas 220 Ace 160

Бренд: REMEHA Страницы: 92

Бренд: Main Heating Страницы: 83

Бренд: Raypak Страницы: 40

Бренд: Unical Страницы: 40

Бренд: R&V Works Страницы: 12

GOLD CGS 550-110-260/0107

Бренд: Weil-McLain Страницы: 64

Бренд: IMI Hydronic Страницы: 8

Бренд: Nibe Страницы: 56

Бренд: BRÖTJE Страницы: 168

Бренд: Sharp Страницы: 12

Бренд: Ecotermal Страницы: 15

Бренд: Crestron Страницы: 60

Бренд: Crest Audio Страницы: 24

RAPAX 200 SOL V3

Бренд: Immergas Страницы: 32

NIKE MYTHOS 24 2E Series

Бренд: Immergas Страницы: 32

Бренд: Wallstar Страницы: 29

Бренд: Ideal Boilers Страницы: 32

Бренд: Weil-McLain Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды