Ideal Boilers Mexico Super FF440 страница 11 Скачать руководство пользователя

Страница: 11 / 44

Mexico Super FF440 - FF480 -

Installation & Servicing

REAR FLUE OUTLET

INSTALLATION

PREPARING THE BOILER

Notes

Before placing the boiler in the selected position any gas and
water connections at the rear of the boiler should be
prepared, due to the possible lack of access.

The pump may be fitted to the FLOW or the RETURN.

Screw the distributor tube (supplied with a 1" BSP x 28mm
copper adaptor) into the selected heating return tapping,
using an appropriate jointing material.

IMPORTANT.

It is

IMPERATIVE

that the index mark on the

distributor tube bush is in alignment with the mark on the
section boss, as shown in Frame 3.

DO NOT disturb it when

connecting subsequent pipework.

Fully pumped systems using more than 1 pump, serving
separate zones, must have a common return connection to
the distributor tube.

Select the desired pumped flow tapping.

Screw the supplied boiler thermostat pocket into the
appropriate front section tapping, using an approved jointing
material. Refer to Tables 5 and 6.

Connect pipe fittings to the rear tappings and plug any
unused tappings.

Note

If using iron elbows fit a short straight connector into the

boiler tapping first, to clear the casing.

Connections - as viewed at front

Thermostat Position

Back Section

Front Section

DHW

Flow Return

Flow

Return

Top

Table 6 - Gravity Domestic Hot Water
and Pumped Central Heating

Table 5 - Fully Pumped Systems

Connections - as viewed at front

Thermostat Position

Back Section

Front Section

Flow

Return

Top

REAR FLUE ASSEMBLY - Exploded view

LEGEND

Terminal.

Weather seal.

Flue assembly.

Boiler sealing ring.

Flue extension tube (long, with ring).

Sealing plate.

Flue connector.

Turret access cover.

Remove the turret access cover.

Locate the LONG flue extension tube (with the air
deflector ring) in the flue accessories pack.

3. FF440 models only.

Undo the 2 self-tapping screws

securing this ring and slide to the centre of the flue tube.

Note.

The boiler turret assembly is factory built, ready for rear flue installation.

Offer the extension tube down through the access hole
and partly out through the rear turret hole.

5. FF440 models only.

Relocate the air deflector ring - it will

only fit one way, due to the offset tabs - and secure its rear
tab in the

rear

hole with a self-tapping screw (inserting this

from the

outside

of the turret).

Pull the flue extension tube foward to the flue connector
and secure to the fan outlet assembly with the M4 screw.

7. FF440 models only.

Refit the front self-tapping screw to

the second fixing tab on the air ring.

200939-1.p65

3/1/2004, 4:33 PM

Содержание Mexico Super FF440













































Результаты поиска

Содержание Mexico Super FF440

Отзывы:

Похожие инструкции для Mexico Super FF440

Бренды по названию

Популярные бренды

Ideal Boilers Mexico Super FF440, Руководство по установке и обслуживанию

Результаты поиска

Содержание Mexico Super FF440

Отзывы:

Похожие инструкции для Mexico Super FF440

Бренды по названию

Популярные бренды