Ideal Boilers Classic HE12 Скачать руководство пользователя

Страница: 34 / 48

Optia HE

Installation & Servicing

SERVICING

Remove the air pressure switch and CO/CO

sensing pipes.

Disconnect the electrical connections.

Remove the 2 fan fixing screws and remove the fan by pulling
forward.

55 CLEANING THE FAN ASSEMBLY / THE FLUEWAYS

56 CLEANING THE BURNER AND PILOT ASSEMBLY

Brush off any deposits that may have fallen on to the
burner head (ensuring the flame ports are unobstructed)
and remove any debris that may have collected.

Note.

Brushes with metallic bristles must not be used.

Remove the main burner injector and ensure there is no
blockage or damage. Clean or renew as necessary.

Refit the injector, using an approved jointing compound
sparingly.

Inspect the pilot burner and ignition / detection electrode.
Ensure that they are clean and in good condition.

Check that:

The pilot burner injector is not blocked or damaged.
Refer to Frame 67 for removal details.

The pilot burner is clean and unobstructed.

The ignition / detection electrode is clean and
undamaged.

The ignition / detection lead is in good condition.

The spark gap is correct (refer to Frame 67) Clean or
renew as necessary.

Note.

The pilot shield is located around the pilot assembly

bracket and is located by the electrode retaining nut.

57 CLEANING THE RECUPERATOR

Remove the 2 rubber grommets to
gain screwdriver access to
remove the side tie rods

retaining

the combustion chamber and
remove the tie rods. (Note. the
combustion chamber is also
retained with 2 front tie rods on the
HE15 and HE18 only.

Remove the combustion chamber.

Remove the sump rubber hose
connection.

Unclip the two side sump
retention clips and remove the
sump.

Pull off the two electrical connections to the flue protection
thermostat.

Clean the sump of any debris.

Clean between the recuperator fins with a
suitable strip of steel.

Slacken the two M5 nuts on the front tie rods, releasing the
tie rods from the combustion chamber.

Unhook the rear collector hood tags and remove collector hood.

Remove the flue baffles.

Remove all loose deposits from the heat exchanger,
particularly between the fins, using a suitable brush.

Check that the fan impellor runs freely. Remove any debris
from the impellor with a soft brush.

10.

Re-assemble in reverse order.

Re-assemble in reverse order, ensuring
rubber grommets are replaced.

SER

VICING

201962-6.pmd

19/02/2008, 15:10

Содержание Classic HE12

















































Результаты поиска

Содержание Classic HE12

Отзывы:

Похожие инструкции для Classic HE12

Бренды по названию

Популярные бренды

Ideal Boilers Classic HE12, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Classic HE12

Отзывы:

Похожие инструкции для Classic HE12

Бренды по названию

Популярные бренды