SET UP MENU
LENS
•
DC
•
MANUAL
EXPOSURE
•
SHUTTER
•
AGC
•
SENS-UP
•
BRIGHTNESS
•
ACCE
•
DEFOG
•
BACKLIGHT
•
RETURN
WHITE BAL
•
ATW
•
AWC
→
SET
•
INDOOR
•
OUTDOOR
•
MANUAL
DAY&NIGHT
•
AUTO
OR
•
B/W
NR
•
2NR
•
3NR
•
LEVEL
•
SMART NR
•
RETURN
SPECIAL
•
CAM TITLE
•
FREEZE
•
MOTION
•
PRIVACY
•
LANGUAGE
•
DEFECT
•
RS485
•
VERSION
•
RETURN
ADJUST
•
SHARPNESS
•
MONITOR
•
OSD
•
LSC
•
NTSC/PAL
•
RETURN
RESET
•
FACTORY
•
RETURN
EXIT
8
9
10
ATW : 1800°K ~ 10500°K.
•
AWC
→
SET : Shoot a white paper push SET button..
•
INDOOR : 4500°K ~ 8500°K.
•
OUTDOOR : 1800°K ~ 10500°K.
•
MANUAL : Select this to fine-tune White Balance manually.
Set White Balance first by using the ATW or AWC mode.
After that switch to MANUAL mode, fine-tune the White
Balance and then press SET button.
•
► RETURN :
RET(RETURN) : Select this to save the setting for this menu and
return to the upper menu.
END : Select this to save the setting for this menu and exit the
SET UP menu.
●
Manual
: Select Manual Lens
●
DC
: Select Auto Iris Lens
When DC is select, you can control screen brightness. The range
of bright control is between 0 and 100 (45 in case of WDR mode).
Adust the brightness appropriately for optimal screen brightness.
►
the BRIGHTNESS LEVEL.
► It may not work properly depending on the installed lens. Set the
Level of the lens to the optimal value.
Some lenses may not work properly, depending on the setting of
‧
SHUTTER : 1/30,FLK, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, x2, X3, AUTO.
‧
AGC : LOW, MIDDLE, HIGH.
‧
SENSE-UP : x2 , x3. (In Auto mode)
‧
BRIGHTNESS : 1 ~ 100.
‧
ACCE (D-WDR) : OFF / LOW / MIDDLE /HIGH
‧
DEFOG : DEFOG or Rain
‧
BACKLIGHT : OFF, BLC,HBLC
–BLC : Enables a user to directly select a desired area from a picture, and to
video the area more clearly.
﹥
GAIN : MIDDLE, HIGH, LOW.
﹥
AREA : Select POSITION, SIZE, RET, AGAIN.
﹥
DEFAULT : Reset the BLC setting to the factory defaults.
﹥
RETURN : (RET / END)
–HSBLC : If there is a high light installed in a limited environment such as an
apartment parking garage or gas station entrance, removing the high
light makes it possible to view car license plates efficiently.
﹥
SELECT : AREA 1 ~ AREA 4.
﹥
DISPLAY : (ON / OFF) You can use
↑
,
↓
,
←
,
→
to adjust POSITION and SIZE.
﹥
LEVEL : 0 ~ 100.
﹥
MODE : ALL DAY / NIGHT.
﹥
BLACK MASK : ON / OFF
﹥
DEFAULT : Reset the HSBLC setting to the factory defaults.
﹥
RETURN : (RET / END)
‧
RETURN : (RET /END)
11
•
AUTO : If use IR LED with Light Sensor, it is no function.
﹣
DELAY : 0 ~ 60 seconds.
﹣
D
→
N (AGC) : 0 ~ 100.
﹣
N
→
D (AGC) : 0 ~ 100.
NR
:
•
2 DNR : OFF/ON
•
3 DNR : OFF/ON
﹣
OFF : Deactivates the DNR Function. Noise in not reduced.
﹣
ON : Activates the DNR so that noise is not reduced.
Press the SET button then you can adjust the noise reduction level.
﹥
S-LEVEL : 0 ~ 100.
﹥
E -LEVEL : 0 ~ 100.
‧
LEVEL : 0 ~ 100.
‧
SMART NR : OFF/ON (SMART NR working when 3DNR level >40)
‧
RETURN : (RET/END)
•
CAM TITLE : If you enter a title, the title will appear on the monitor.
- OFF : No title will be displayed on the monitor even if you enter one.
- ON : Press the SET button to the menu.
Use the 4 direction button to move to a desired letter and select the
letter by pressing the SET button. Repeat this to enter multiple letters.
You can enter up to 15 letters.
Enter a title, move the cursor to “POS” and press
SET button. The entered title appears on the screen.
Select the positon to displayed the title on the screen
by using the 4 direction button and press the SET
button. When the position is determined, select
“END” and press the SET button to return to the
SPECIAL menu.
ABCDEFGHIJK
LMNOPQRSTUV
WXYZ► ( )
- _
■ / = & : ~ , .
1 2 3 4 5 6 7 8 9
→ ←
CLR POS END
►If you move the cursor to CLR and press the SET button, all the
letters are deleted. To edit a letter, change the cursor to the bottom
left arrow and press the SET button. Move the cursor over the letter
to be edited, move the cursor to the letter to be inserted and then
press the SET button.
•
COLOR : This picture is always displayed in color.
•
B/W : This picture is always displayed in black and white.
-BURST : (ON / OFF)
-IR SMART : OFF / ON
>LEVEL : 0 ~ 15
>AREA : You can use
↑
,
↓
,
←
,
→
to adjust POSITION and SIDE.
>IR LED : ON / OFF
>IR PWM : 0 ~ 15
>RETURN : RET / END
