ICU EVE Скачать руководство пользователя страница 5

 
 

   

Charging point installation 

1.  Fold open the packaging to first remove the white front cover. The 

front cover is fixed to the charging unit with two screws on the top 
and bottom sides. Loosen the screws at the bottom using a hexagon 
socket wrench and loosen the two screws on the bottom side of the 
rear cover using M5 Torx (T25). Tilt the front cover up on the bottom 
side. 

Note

: The wiring of the LEDs and optional display is fixed on 

both the front cover and the rear cover. Ensure that this wiring is first 
disconnected. Next, lay the front cover down.

 

2.  Use the drilling template on the cardboard packaging that has been 

marked with a drill icon to draw holes at the required height. 

Note

use the drilling template and not the rear cover. Use a spirit level to 
draw the markings straight. The distance between the holes is 123.8 
mm (at the top), 39.6 mm (at the bottom) and 434.3 mm (vertically). 
Fix the suspension block using the bottom two holes that have been 
drilled. 

3.  Allow the charging point to drop on the suspension block 

perpendicularly (fig. 1). 

4.  Fix the charging point at the top side using 2 screws with a cross 

section of no more than 8 mm. (Fig. 1.) 
 

 

Figure 1: 3-phase model shown 

 

Содержание EVE










Отзывы: