Supported Standards
VXI-11 Capabilities
Fully VXI-11.3 compliant
VXI-11.3
Device Interface
Sockets
15 + 1 for UDP
Channel types Data, Abort and Interrupt
Links
64
Interface Names inst0 for general use
inst1 for transparent data
VXI-11.3 Functions
All VXI-11.3 functions including device read,
write, local, remote, clear, trigger, readstb, lock
and unlock.
RPC Protocol
Conforms to ONC RPC Version 2, VXI-11
Ethernet Interface
Type
IEEE 802.3 compliant
Speeds
10BaseT (10 Mb/s)
100BaseT (100 Mb/s)
IP Address
Static or DHCP
Factory setting 192.168.0.254 static
Interface name any [inst0], [inst1]
WebServer Capabilities
Provides the following HTML 4.01 compatible
web pages:
Welcome
Configuration
Confirmation
Reboot
IEEE 488.2 Capabilities:
Runs all required 488.2 Common Commands,
incorporates an extended IEEE-488.2 Status
Reporting Structure and the Message Exchange
Protocol.
SCPI Capabilities:
Incorporates the SCPI Command Tree shown in
Figure 2. Complies with SCPI version 1994.0
8013: SPECIFICATIONS
Signal Characteristics
The 8013's parallel I/O signals have the follow-
ing electrical characteristics. All time delays
listed here are maximums, all pulse widths are
minimums.
Inputs
128 Digital I/O ,
2 Status and Reset Inputs
Input
High = > +2.0 V @ ±10 µA
Logic
Low = <0.8 V @ 250 µA
Levels
with 33 Kohm pullup to +5 Vdc for
sensing contacts.
Max High = 5.5 V
Input
External Data Inhibit line
Timing
SETS within 1 µs of the active edge
of the EDR Input signal and resets
after data is loaded. Data loading
time for 6 BCD/HEX characters is
0.15 ms (typ.) after the 8013 has been
addressed as a Talker
Output
High = >3 V with 3 mA source
Logic
High =>2 V with 24 mA source
Levels
Low = 0.0 to +0.55 Vdc, 48 mA sink
Output
Data is transferred to the
Timing
output 2 to 3 ms after receipt of a
message depending upon data trans-
fer mode and command.
Pulse width 10 to 30000 ms
Data Stb
Output pulse width, 5 µs.
Trigger
Output pulse width, 5 µs
Remote
Output level asserted when in the
remote state
Reset
Output pulse width, 70 µs when
8013 reset.
Table 2 Digital IO Functions
Input Bytes
Input Signal polarity
Input Handshaking
Talk data format
Talk data conversion table
Output Bytes
Output Polarity
Output Handshaking
Listen data format
Control line polarities
SENSe input polarities
STATus register configurations
SOURce output polarities
Controls and Indicators
CONTROLS
LAN Rst Board edge push-button
LEDs
PWR
Indicates power on
LAN
Unit good and connected to an active
network
ACT
Transferring messages to/from
the network
RDY
Unit has passed self test
TALK Unit is addressed to talk
LSTN Unit is addressed to listen
SRQ
SRQ asserted on GPIB bus
ERR
Blink for a detected soft error or
solid On for a command error
Physical
Size, L x W x H
7.0 x 5.5 x 0.55 inches (178 x 140 x 14 mm)
Material
PCB
FR406 Fiberglass
Components
RoHS compatible
Construction
Lead Free
Connector and Headers
Digital I/O:
150-pin, 3 row male conn
Ethernet:
RJ-45
Temperature
Operation
-10° C to +70° C
Storage
-20° C to +85° C
Humidity
0-90% RH without condensation
Power
+5 Vdc @ 500 mA (typ)
Included Accessories
Instruction Manual
Support CD with sample programs
LAN Crossover Cable
Available Accessories
See Ordering Guide on page 5 for a complete list
of accessory items.
Mating short connector, P/N 902308
Mating tall connector, P/N 902331
Wiring Kit w/1 ft cable, P/N 115606
Wiring Kit w/2 ft cable, P/N 115607
Shielded Bulkhead Adapter, P/N 902329
4813 Relay Driver Board, P/N 115490
4813 DC-37 Relay Driver Board, P/N 115790
Data subject to change without notice. Copyright 2010 ICS Electronics
03/10
