manualshive.com logo in svg

ICS Advent 486MBS Series, Руководство по эксплуатации продукта

Поделиться
Скачать
ICS Advent 486MBS Series Скачать руководство пользователя страница 35

Chapter 2:  WinBIOS Setup

Manual Number: 41209-103-1

Page 2-9

Onboard FDC

This option enables the floppy drive controller on the motherboard. The settings are 

Enabled,

Disabled 

or

 Auto.

  The default setting are

 Auto.

Onboard Serial Port1

This option enables serial port 1 on the motherboard and specifies the base I/O port address for

serial port 1.  The settings are 

Auto, Disabled, 3F8h, 2F8h, 3E8h, 

or

 2E8h

.  The Optimal and Fail-

Safe default settings are 

Auto

.

Onboard Serial Port2

This option enables serial port 2 on the motherboard and specifies the base I/O port address for

serial port 2.

The settings are 

Auto, Disabled, 3F8h, 2F8h, 3E8h, 

or

 2E8h.

 The Optimal and Fail-Safe default

settings are 

Auto

.

Onboard Parallel Port

This option enables the parallel port on the motherboard and specifies the parallel port base I/O

port address. The settings are 

Auto, Disabled, 378, 278,

 or 3BC

.

  The Optimal and Fail-Safe default

setting are 

Auto.

Parallel Port Mode

This option specifies the parallel port mode. ECP and EPP are both bi-directional data transfer

schemes that adhere to the IEEE P1284 specifications. The settings are 

Normal, Bi-Dir, EPP, 

or

ECP. 

 The default settings are 

Normal.

Parallel Port DMA

This option is only available if the setting for the 

Parallel Port Mode

 option is 

ECP.

The settings are 

0, 1, 

or

 3

. The default setting is 

3. 

 

Refer to Hardware Jumper settings in Chapter

One for JP 15 and JP16 when setting for these options.

Parallel Port IRQ

The settings are 

5

 and

 7. 

 The default setting is 

5.

Onboard  IDE

This option specifies the onboard IDE controller channels that will be used. The settings are 

Dis-

abled, Both

,

 Primary 

or 

Secondary.

 The Optimal and Fail-Safe default settings are 

Primary

.

Содержание 486MBS Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды