ICP Electronics NOVA-7895 страница 15 Скачать руководство пользователя

Страница: 15 / 48

NOVA-7895 Socket 370 Celeron

& Pentium III

Multimedia & Dual Ethernet ,IEEE1394, Embedded Board

You can connect them to your LAN via RJ45 connectors. The pin
assignments are as follows.

•

CN12,19 : LAN RJ45 Connector

1 TX+

5. N/C

2 TX-

6. RX-

RX+

N/C

CN12 ,CN19 : PCI BUS Realtek 8100B LAN

CN12 Ethernet LED setup

LED Description
CN6 Speed
CN7 Active

CN19 Ethernet LED setup

LED Description

CN13 Speed
CN14 Active

3.11 Fan Connector

The NOVA-7895 provides one CPU cooling fan connector and
one system fan connector, which can supply 12V/500mA to the
cooling fan.

•

CN4 : CPU Fan Connector

PIN NO.

DESCRIPTION

1 GND
2 +12V
3 Fan

Sensor

3.12 Temperature Sensor Connector

You can connect an external temperature sensor to this connector.

NOVA-7895 Socket 370 Celeron

& Pentium III

Multimedia & Dual Ethernet ,IEEE1394, Embedded Board

•

CN8 : Temperature Sensor Connector

                    **  Use 10K Ohm Temperature register
                         sensor

Pin No. Description Pin No. Description

1 THER-DA

GND

3.13 Audio CD IN

This is used to connect to CD-Out from the CD-ROM player.

•

CN25 : Audio CD IN ( 2.54mm )

Pin No. Description Pin No. Description
1

CD IN_R 2

GND

CD IN_L

3.14 Audio Speaker OUT ( Reserved )

•

CN24 : Left/Right Audio SPK Output Connector

           via optional amplifier Speaker Output .
             (Two 6W stereo power amplifiers )

1.  ( SPK Right Out)
2.  GND
3.  GND
4.   ( SPK Left Out)

3.15 Audio Panel

One line-out ( 2 different pin assignments ), one line-in and one
mic-in are supported via and un-amplified audio chip.

•

CN28 : Audio Panel

Содержание NOVA-7895

















































Результаты поиска

Содержание NOVA-7895

Отзывы:

Похожие инструкции для NOVA-7895

Бренды по названию

Популярные бренды

ICP Electronics NOVA-7895, Руководство пользователя

Результаты поиска

Содержание NOVA-7895

Отзывы:

Похожие инструкции для NOVA-7895

Бренды по названию

Популярные бренды