background image

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures: 

-Reorient or relocate the receiving antenna. 

-Increase the separation between the equipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your 

authority to operate the equipment. 

9

Содержание iCamera 1000












Отзывы: