19
6
1. Identify the Front Stabiliser (2). While another person
lifts the front of the Frame (1) slightly, attach the Front
Stabilizer to the Frame with two M10 x 65mm Carriage
Bolts (65) and two M10 Black Nylon Locknuts (63).
Make sure that the Front Stabiliser is turned so the
Wheels (50) are not touching the floor.
2
50
50
63
65
1
1
2. While another person lifts the back of the Frame (1)
slightly, attach the Rear Stabilizer (9) to the Frame with
two M10 x 65mm Carriage Bolts (65) and two M10
Black Nylon Locknuts (63).
65
9
1
3
13
1
36
73
64
14
14
14
71
70
64
2
63
63
4. The Console (16) requires four “D” batteries (not
included); alkaline batteries are recommended.
Remove the screw from the battery drawer. Pull the
battery drawer open and insert four batteries.
Make
sure that the batteries are oriented as shown by
the markings inside the battery drawer. Close the
battery drawer and reattach the screw. Note: When the
batteries are installed correctly, the fan will turn on for a
moment.
16
Batteries
Battery
Drawer
4
Screw
Inspect and tighten all parts of the exercise cycle reg-
ularly. Replace any worn parts immediately.
To clean the exercise cycle, use a damp cloth and a
small amount of mild detergent.
Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands or holding the metal con-
tacts too tightly whilst using the handgrip pulse sen-
sor. Excessive movement or pressure may interfere
with heart rate readings.
• For the most accurate heart rate reading, hold the
metal contacts for about 15 seconds.
• Keep the metal contacts clean. The contacts can be
cleaned with a soft cloth—never use alcohol,
abrasives, or chemicals.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. In order to adjust the
reed switch, the Left Side Shield (17) must be
removed. Remove the seven Screws (52) from the
Right Side Shield (18). Next, remove the Screw (59)
from the right side of the Side Shield Cover (19).
Using an adjustable wrench, turn the Left Pedal (24)
clockwise and remove it. Next, remove the two
Screws (66) from the Left Side Shield (17). Remove
the Screw (59) from the left side of the Side Shield
Cover (19) and lift it off. Gently remove the Left Side
Shield.
Next, locate the Reed Switch (43). Turn the Left
Crank Arm (42) until the Magnet (38) is aligned with
the Reed Switch. Loosen but do not remove the
Screw (66). Slide the Reed Switch slightly closer to or
away from the Magnet. Retighten the Screw. Turn the
Crank for a moment. Repeat until the console dis-
plays correct feedback. When the Reed Switch is cor-
rectly adjusted, reattach the left side shield, side
shield cover and the pedal.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. See assembly step 4 on page
6 for replacement instructions.
MAINTENANCE AND TROUBLESHOOTING
52
66
59
59
18
19
17
42
38
43
66
24
19
52
3. Whilst another person holds the Upright (13) in the
position shown, connect the Upper Wire Harness (36)
to the Lower Wire Harness (73).
Slide the Upright (13) onto the Frame (1).
Be careful to
avoid pinching the Wire Harnesses (36, 73). Attach
the Upright to the Frame with three M8 x 25mm Button
Screws (14) and three M8 Split Washers (64).
Attach the Water Bottle Holder (70) to the Upright (13)
with two M4 X 22mm Screws (71).
