11
14
Turn on the console.
Note: The console requires four 1.5V “D” batteries
(see assembly step 4 on page 6).
To turn on the console, press the On/Reset button
or begin pedaling. (See the drawing on page 10 to
identify the On/Reset button.)
Select the manual mode.
Each time the console is
turned on, the manual
mode will be selected. If a
program has been select-
ed, select the manual
mode by pressing the
Program button repeated-
ly until the letters RPM
appear in the small display.
Begin pedaling and change the resistance of
the pedals as desired.
As you pedal, change the resistance of the ped-
als by pressing the + and – buttons below the
large display. There are ten resistance levels—
level 10 is the most challenging. Note: After the
buttons are pressed, it will take a few seconds for
the resistance to reach the selected setting.
Follow your progress with the small display
and the large display.
The small display will
show your pedaling pace,
in revolutions per minute
(RPM). The indicator bar
in the small display will
increase or decrease in
length as you increase or
decrease your pedaling
pace.
The upper sec-
tion of the
large display
will show the
distance you
have pedaled
and the numbers of calories and fat calories you
have burned (see FAT BURNING on page 20 for
an explanation of fat calories). The display will
change from one number to the next every few
seconds. If you use the handgrip pulse sensor,
the display will also show your heart rate (see
step 5 on page 12).
To view only the distance
you have pedaled or the
number of calories or fat
calories you have burned,
press the upper button on
the left side of the large
display until only the word
DISTANCE, CALORIES, or
FAT CALORIES appears in the upper section of
the large display; make sure that the word SCAN
does not appear. To again view the distance you
have pedaled and the numbers of calories and
fat calories you have burned, press the upper
button until the word SCAN reappears.
The centre of
the large display
will show the
elapsed time and
your current pace
(pace is shown in
minutes per mile in this section of the large dis-
play). The display will change from one number
to the other every few seconds. Note: When a
program is selected, the display will show the
time remaining in the program instead of the
elapsed time.
To view only the elapsed time or your pace, press
the centre button on the left side of the large dis-
play until only the word TIME or PACE appears;
make sure that the word SCAN does not appear.
To again view both the elapsed time and your
pace, press the centre button until the word
SCAN reappears.
The lower sec-
tion of the large
display will show
your pedaling
speed and the
resistance level.
The display will change from one number to the
other every few seconds.
To view only your pedaling speed or the resis-
tance level, press the lower button on the left
side of the large display until only the word
SPEED or RESISTANCE appears; make sure
that the word SCAN does not appear. To again
view both your pedaling speed and the resistance
level, press the lower button until the word SCAN
reappears.
4
3
2
1
HOW TO USE THE MANUAL MODE
Indicator Bar
Upper Button
To use iFIT.com CDs, the exercise cycle must be con-
nected to your portable CD player, portable stereo, home
stereo, or computer with CD player. See pages 14 and
15 for connecting instructions.
To use iFIT.com video-
cassettes, the exercise cycle must be connected to your
VCR. See page 16 for connecting instructions.
To use
iFIT.com programs directly from our Web site, the
exercise cycle must be connected to your computer. See
page 15.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the LINE OUT jack on your CD
player. Plug your headphones into the PHONES
jack.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the splitter. Plug the splitter into the
PHONES jack on your CD player. Plug your head-
phones into the other side of the splitter.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the adapter. Plug the adapter into an
AUDIO OUT jack on your stereo.
B. See the drawing above. Plug one end of the audio
cable into the jack beneath the console. Plug the
other end of the audio cable into the LINE OUT jack
on your stereo. Do not use the adaptor.
C. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the splitter. Plug the splitter into the
PHONES jack on your stereo. Plug your head-
phones into the other side of the splitter.
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER
LINE OUT
PHONES LINE OUT
PHONES
Audio
Cable
Head-
phones
A
PHONES
PHONES
Audio
Cable
Splitter
Headphones
B
AUDIO OUT
RIGHT
LEFT
Audio
Cable
Adapter
A/B
PHONES
Audio
Cable
C
Splitter
Headphones
