11
3
BASIC OPERATION
■
TRAILS function
The trails function memorizes echoes continuously or
at constant intervals. This is useful for watching other
ships’ tracks, approximately relative speed, etc.
3/4
(0.25)
M.TUNE
1:05
NM
CURS
STW 15.7KT
H UP
HDG 253.9˚T
6M
TRAILS
IR
ES
T.VECT
0.453NM
TRAIL
indicator
Trail interval
counter
Trail time
Trail time
•
Setting the trail interval time
q
Push [MENU]/[
] to call up the VIDEO menu.
• Push
[
q
]
one or more times until the “TRAIL TIME” sec
-
tion becomes highlighted.
w
Push [
t
] [
u
] to select trail interval time.
• 6 seconds, 15 seconds, 30 seconds, 1 minute, 3 min
-
utes, 6 minutes, 15 minutes and
∞
(continuous) are se-
lectable.
e
Push [MENU] one or more times to exit the menu.
•
Using the TRAILS function
q
Push [TRAILS]/[
] to turn ON the trail func-
tion.
• “TRAILS” and trail interval time appears in the upper
right of the screen.
• Trail interval counter starts to count up to the trail time.
w
All displayed echoes at the plotted time are mem-
orized and displayed with a graduated intensity
together with the current echoes.
• Echoes are displayed with minimum intensity when “
∞
”
is selected.
e
Push [TRAILS]/[
] to cancel the trail function
and erase the plotted echoes.
• “TRAILS” and trail interval time disappears.
■
Power save function
The power save function conserves the boat’s battery
power by pausing the transmission. The standby
(pausing) times are selectable (rotation number is
fixed to 10).
For example, when 1 minute is selected, the scanner
rotates 10 revolutions; then stops for 1 minute, and
then repeats this sequence while the power save func-
tion is activated.
CURS 3 4 ˚ 3 7 . 7 2 N
CURS 3 4 ˚ 3 7 . 7 2 N
1
(0.25)
T.VECT 6M
0.900NM
NM
CURS
SOG17.7KT
H UP
014.6˚T
HDG273.9˚T
IR
ES
E B L 1
E B L 2
MOB
V R M 1
V R M 2
1 3 5 ˚ 3 4 .4 2 E
0:48
SAVE
Hold down [TX] for 1 second
to turn the SAVE function on.
Scan and STBY alternates
Count down the standby time
1
(0.25)
T.VECT 6M
0.900NM
NM
CURS
SOG17.7KT
H UP
014.6˚T
HDG273.9˚T
IR
ES
E B L 1
E B L 2
MOB
V R M 1
V R M 2
1 3 5 ˚ 3 4 .4 2 E
0:00
SAVE
COMPASS
GPS
COMPASS
GPS
D
Setting the scanning standby time
q
Push [MENU]/[
] four times to call up the INT.
SETTING menu.
w
Hold down [
q
] until the “SAVE TIME” section
becomes highlighted.
e
Push [
t
] [
u
] to select standby time.
• 1, 6, 15, and 30 minutes are selectable.
r
Push [MENU]/[
] twice to exit the menu display.
D
Using the power save function
q
Hold down [TX (SAVE)]/[
] for 1 second to
turn ON the power save function.
• The save indicator appears in the top of the screen.
w
After the scanning rotations are finished, transmis-
sion and rotation are suspended until the selected
standby time elapses.
• The display shows the last scanned echoes until the
scanning restarts.
• “SAVE” and standby time appear in the top of the screen
and the standby time is counted down.
e
After the selected standby time elapses, transmis-
sion and rotation restart.
r
Push [TX (SAVE)]/[
] to cancel the power
save function.
• The save indicator turns OFF.
NOTE:
When you use the power save function
together with the alarm function, the CRT display is
turned OFF until an object enters the programmed
alarm zone, therefore, more power saving is
possible. (p. 16)
