Icom iM506 Скачать руководство пользователя страница 73

Страница: 73 / 124

DSC OPERATION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Receiving a Test Call

When a Test Call is received:

➥

The alarm sounds for 2 minutes.

➥

“RCVD TEST CALL” appears. The LCD backlight blinks for
2 minutes.

Push [ALARM OFF] to stop the alarm and the blinking

backlight.

• Even if you do not push [ALARM OFF], the alarm stops after 2

minutes, and then the screen in step

is displayed.

Push a softkey to select your desired action.

[IGN]

➥

Push to ignore the Call and return to the normal operat-
ing mode.

• The transceiver exits the DSC mode.

• The “

” icon continues to blink and the Call is stored in the

Received Call Log.

[INFO]

➥

Push to display the Received call information. (p. 65)

[ACK]

➥

Push to display the “TEST ACK” screen to reply to the
Call. (p. 45)

When “TEST ACK” is set to “Auto TX,” the transceiver au-

tomatically replies to the Call. In that case, both the TX and
RX calls are stored in the Transmitted and Received Call
Logs.

Содержание iM506





























































































































Результаты поиска

Содержание iM506

Отзывы:

Похожие инструкции для iM506

Бренды по названию

Популярные бренды

Icom iM506, Инструкция по эксплуатации

Результаты поиска

Содержание iM506

Отзывы:

Похожие инструкции для iM506

Бренды по названию

Популярные бренды