
4 - 1
SECTION 4 CIRCUIT DESCRIPTION
4-1 RECEIVER CIRCUITS
4-1-1 TRIPLEXER CIRCUIT (MAIN UNIT)
The transceiver has a triplexer (low-pass and high-pass
filters) on the first stage from the antenna connector
(CHASSIS; J2) to separate the signals into VHF, UHF and
800 MHz band signals. The 2 of low-pass filters (L51, L52,
L56, C295, C299 and L45, L46, L49, C282, C285, C289)
are for VHF band signals, the low-pass (L51, L52, L56,
C295, C299) and high-pass (L47, L50, C284, C288, C292,
C586) filters are for UHF band signals and high-pass filter
(L55, L58, C298, C302, C304) is for 800 MHz band signals.
The separated signals are applied to each antenna switching
circuits .
4-1-2 ANTENNA SWITCHING CIRCUITS (MAIN UNIT)
The antenna switching circuit (VHF: D50, UHF: D51)
functions as a low-pass filter while receiving. However,
its impedance becomes very high while transmitting.
Thus transmit signals are blocked from entering the
receiver circuits. The antenna switching circuit employs a
1
⁄
4
λ
type diode switching system.
800 MHz band signals pass through the antenna switch
(D44).
The passed signals are then applied to the each attenuator
circuits.
4-1-3 ATTENUATOR CIRCUITS (MAIN UNIT)
The attenuator circuit attenuates the signal strength to a
maximum of 10 dB to protect the RF amplifier from distor-
tion when excessively strong signals are received.
The RF signals from the antenna switching circuits pass
through the each attenuator circuit (for VHF band is D49, for
UHF band is D46 and D48, for 800 MHz band is D39).
The D/A converter outputs “ATT” signal (IC11, pin 6), and is
then applied to the attenuator controller (Q44). The circuit
output attenuator control signals to each attenuator circuits.
The attenuated signals are applied to the each RF circuits.
4-1-4 RF CIRCUITS (MAIN UNIT)
The RF circuit amplifies signals within the range of frequen-
cy coverage and filters out-of-band signals.
• VHF BAND RF CIRCUIT (118–174 MHz)
The RF signals from the attenuator circuit pass through the
tunable bandpass filter (D41, L40, L44, C273, C280). The
filtered signals are amplified at the RF amplifier (Q38) and
are then applied to the another 3-stage tunable bandpass
filter (D22, D23, D29, L28, C171, C174, C176, C177, C181,
C185, C191, C198, C201, C204, C208) to suppress unwant-
ed signals and improve the selectivity. The filtered signals
are applied to the VHF 1st mixer circuit (Q32).
• UHF BAND RF CIRCUIT
(EXP: 430–440 MHz, USA: 440–450 MHz)
The RF signals from the attenuator circuit are applied to the
RX switch (D42). The switched signals are amplified at the
RF amplifier (Q39) and are then applied to the bandpass
filter (FI4) to suppress unwanted signals. The filtered signals
are applied to the UHF 1st mixer circuit (Q35).
LPF
VHF band (118−174 MHz)
to the 2nd IF circuit
1st mixer (Q32)
Q38
Q39
D9
D8
D10
D17
D18
Q36
Q37
Q41
Q40
D44
D43
D42
1st mixer (Q35)
1st mixer (IC12)
Antenna
UHF band (EXP: 430−440 MHz, USA: 440–450 MHz)
LPF
T/R
SW
BPF
RF
AMP
BPF
ATT
IF
SW
800M band (810−1000 MHz)
HPF
ANT
SW
BPF
RF
AMP
BPF
ATT
BAND
SW
RF
AMP
HPF
T/R
SW
RF
AMP
BPF
BPF
ATT
IF
SW
BAND
SW
400M band (230−550 MHz)
BPF
RF
AMP
IF
SW
BAND
SW
BAND
SW
RF
AMP
• RF AND IF CIRCUITS
Содержание ID-800H
Страница 3: ...SERVICE MANUAL VHF UHF DIGITAL TRANSCEIVER S 14121HZ C1 May 2005 ...
Страница 59: ...S 14121HZ C1 2005 Icom Inc ...