Icom IC-R2500 Скачать руководство пользователя

Страница: 36 / 53

SCAN OPERATION

Scan edges can be programmed in the same manner as
memory channels. Scan edges are programmed into scan
edges, 0A/0B to 49A/49B, in memory channels.

Push the desired band’s [VFO/MR•S.MW] once or twice
to select VFO mode.

Set the edge frequency of the desired frequency range:

➥

Set the frequency using the same band’s [DIAL].

➥

Set other data (e.g. tone squelch, etc.), if desired.

Push and hold the same band’s [VFO/MR•S.MW] for
1 sec. to enter select memory write mode.

• “

” indicator and the memory channel number blink.

Rotate [DIAL] to select one of scan edge channel, 0A to
49A.

Push and hold [VFO/MR•S.MW] for 1 sec. to program.

• 3 beeps sound and VFO mode is automatically selected.
• Scan edge 0B to 49B is automatically selected when continuing

to hold [VFO/MR•S.MW] after programming.

To program a frequency for the other pair of scan edges,
0B to 49B, repeat steps

• If the same frequency is programmed into a pair of scan edges,

programmed scan will not function.

[EXAMPLE]: Programming 144.000 MHz into scan edge 1A.

Push

Rotate for setting frequency, etc.

Push for 1 sec.

Rotate

Push for 1 sec. and continue to push

➠

Beep

“

Beep

“

Beep

“

S.MW

VFO/MR

S.MW

VFO/MR

S.MW

VFO/MR

Release

S.MW

VFO/MR

■

Scan edges programming

Содержание IC-R2500






















































Результаты поиска

Содержание IC-R2500

Отзывы:

Похожие инструкции для IC-R2500

Бренды по названию

Популярные бренды

Icom IC-R2500, Инструкция по эксплуатации

Результаты поиска

Содержание IC-R2500

Отзывы:

Похожие инструкции для IC-R2500

Бренды по названию

Популярные бренды