manualshive.com logo in svg

Icom IC-F4SR, Инструкция по эксплуатации

Поделиться
Скачать
Icom IC-F4SR Скачать руководство пользователя страница 25

21

9

TROUBLESHOOTING

If your transceiver seems to be malfunctioning, please check
the following points before sending it to a service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

REF.

No power comes ON.

• The battery is exhausted.
• Bad connection to the battery pack.

• Recharge the battery pack.
• Check the connection to the transceiver.

p. 18

—

No sound comes from
the speaker.

• Volume level is too low.
• Different tone or code is selected.

• Set [VOL] to a suitable level.
• Check the tone using tone scan.

p. 5
p. 15

Transmitting is impossi-
ble.

• The battery is exhausted.

• Recharge the battery pack.

p. 18

The displayed channel
cannot be changed.

• Lock function is activated.

• Push [

] for 2 sec. to cancel the func-

tion. 

p. 6

Scan starts automati-
cally.

• The auto channel function is activated.

• Turn the auto channel function OFF.

p. 11

No beeps sound.

• Confirmation beeps are turned OFF.

• Turn confirmation beeps ON in set mode.

p. 16

No contact possible with
another station.

• Different channel is selected.
• Different tone or code is selected.

• Use scan in all channel mode.
• Check the tone using tone scan.

p. 9
p. 15

Содержание IC-F4SR





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды