background image

i

INTRODUCTION

FOREWORD

Thank you for choosing this Icom transceiver.

IMPORTANT

FIRST, CAREFULLY READ THE INSTRUCTION MANUAL

 

that is provided with the transceiver.

SAVE THESE OPERATING INSTRUCTIONS—

 

These operating instructions contain additional important 

operating instructions for the 

IC-F29DR dPMR446/PMR446 TRANSCEIVER

.

This transceiver includes some functions that are usable only when they are preset by your dealer. Ask your Icom 

dealer or system operator for details.

Icom, Icom Inc. and the Icom logo are registered trademarks of 

Icom Incorporated (Japan) in Japan, the United States, the United 

Kingdom, Germany, France, Spain, Russia, Australia, New Zealand,  

and/or other countries.

dPMR and the dPMR logo are trademarks of the dPMR MoU 

Association.

All other products or brands are registered trademarks or 

trademarks of their respective holders.

TABLE OF CONTENTS

FOREWORD .............................................................. i

IMPORTANT ............................................................... i

1. ACCESSORIES .................................................... 1

Attaching or detaching accessories ........................... 1

 

D

Battery pack ...........................................................1

 

D

Belt clip ..................................................................1

 

D

Jack cover ..............................................................2

2. PROGRAMMABLE KEY FUNCTIONS ................. 3

Programmable key functions ..................................... 3

3. LED INDICATOR ................................................... 5

About the LED indicator............................................. 5

4. SETTINGS............................................................. 7

Setting the Beep function .......................................... 7
Setting the beep and announcement level ................ 8
Setting the Call-Ring ringer ....................................... 9
Setting the ringer level ............................................. 10
Setting the microphone gain .....................................11
Setting the squelch level.......................................... 12
Setting the VOX function ......................................... 13
Setting the VOX gain ............................................... 14

5. dPMR™ OPERATION ......................................... 15

Receiving and transmitting ...................................... 15

 

D

Receiving .............................................................15

 

D

Transmitting .........................................................16

Break-in function...................................................... 17

 

D

Receiving .............................................................17

 

D

Transmitting .........................................................17

Status call ................................................................ 18

 

D

Receiving .............................................................18

6. OTHER FUNCTIONS .......................................... 19

Setting a scan type .................................................. 19
Tone Scan function .................................................. 20

Содержание IC-F29DR
























Отзывы: