-12-
iCharger Synchronous Balance Charger/Discharger 1010B/106B
“Storage” charge/discharge a Lithium battery
This mode is for charging/discharging a Lithium battery that is not to be used for an extended period. The
program determines whether to charge or discharge the battery based on the configured target voltage and
the measured initial voltage of the battery. The nominal target storage voltage depends on the type of Lithium
battery: 3.75V/cell for Lilo, 3.85V/cell for LiPo and 3.3V/cell for LiFe. If at the start the battery voltage exceeds
the target storage voltage the program will start to discharge rather than charge.
Discharging a Lithium battery
In this mode, you can set the target per-cell voltage and hence the final voltage (final voltage=cell
voltage*number of cells). The lowest allowable cell voltage depends on the type of Lithium battery: 2.50V for
Lilo, 3.00V for LiPo and 2.00V for LiFe per cell. If the battery is connected to the balance port, the
iCharger
can
monitor the individual cell voltages. The discharge will stop immediately if any cell falls below the
configured final voltage.
Storage of Lithium battery. The left side of the first line shows the type of
battery you selected in the
User setup
(LiPo, Lilo or LiFe). The value on the
left side of second line sets the charge/discharge current and the value on
the right side of second line sets the cell count and voltage of the battery
pack. After setting the current and voltage, press
Start/Enter
for more than
3 seconds to start the next process.
Charge current: 0.05 – 10A, Voltage: 1 – 10 series (1 – 6 series for 106B)
The number of cells you set and the processor detects. The left side of the
first line ’R:xxSER’ shows the number of cells detected by the
iCharger
and
the right side of the first line ’S:xxSER’ is the number of cells set by the user.
If the numbers are different you should make sure that the configured
number and the actual number for the battery are the same and then you
can start charging by pressing
Start/Enter
. If not, press
Batt type/Stop
to
go back to the previous screen and adjust the setting.
Lithium STORAGE charging mode. The screen shows the status during the
charging process. You can stop charging at any time by pressing
Batt
type/Stop
. Press
Inc
to display each cell’s voltage (see the balance
voltage information) and press
Dec
to display the General Status
information.
Discharge Lithium battery. The left side of the first line shows the type of
battery you selected in the
User setup
(LiPo, Lilo or LiFe) and the value on
the right side shows the final discharge voltage of each cell. The value on
the left side of second line sets the charge current and the value on the right
side of second line sets the cell count and voltage of the battery pack. After
setting the current and voltage, press
Start/Enter
for more than 3 seconds
to start the next process.
Per-cell final voltage:
LiPo (3.00 – 4.20V), Lilo(2.50 – 4.10V), LiFe(2.00 – 3.60V)
Discharge current: 0.05 – 7A , Cell count: 1 – 10S (1 – 6S for 106B)
The number of cells you set and the processor detects. The left side of the
first line ’R:xxSER’ shows the number of cells detected by the
iCharger
and
the right side of the first line ’S:xxSER’ is the number of cells set by the user.
Usually, the auto-detect number won’t lower than the number set by the
user. If the numbers are different you should make sure that the configured
number and the actual number for the battery are the same and then you
can start charging by pressing
Start/Enter
. If not, press
Batt type/Stop
to
go back to the previous screen and adjust the setting.
Discharge process. The
iCharger
allow its user to alter the discharging
current during the process. Press
Start/Enter
to make the discharge current
blink then press
Inc
to increase or press
Dec
to decrease the value and
press
Start/Enter
to confirm the alteration. You can stop discharging at any
time by pressing
Batt type/Stop
. Press
Inc
to display each cell’s voltage
(see the balance voltage information) and press
Dec
to display the
General Status information.
LiPo DCHG 3.30V
LiPo DCHG 3.30V
LiPo DCHG 3.30V
LiPo DCHG 3.30V
1.0A 11.1V(3S)
1.0A 11.1V(3S)
1.0A 11.1V(3S)
1.0A 11.1V(3S)
Start/Enter
>3 seconds
Batt type
stop
R:03SER S:03SER
R:03SER S:03SER
R:03SER S:03SER
R:03SER S:03SER
CONFIRM(ENTER)
CONFIRM(ENTER)
CONFIRM(ENTER)
CONFIRM(ENTER)
Start/Enter
Batt type
stop
Battery
Series
V-BP
Charge
Current
Li03 1.0A 12.60V
Li03 1.0A 12.60V
Li03 1.0A 12.60V
Li03 1.0A 12.60V
DSC 00993 059
DSC 00993 059
DSC 00993 059
DSC 00993 059:
:
:
:51
51
51
51
battery
voltage
number
of cells
discharge
capacity
discharging
time
discharge
current
work
state
-
Dec
+
Inc
-
Dec
+
Inc
R:03SER S:03SER
R:03SER S:03SER
R:03SER S:03SER
R:03SER S:03SER
CONFIRM(ENTER)
CONFIRM(ENTER)
CONFIRM(ENTER)
CONFIRM(ENTER)
Start/Enter
Batt type
stop
Battery
Series
V-BP
Charge
Current
Li03 1.0A 12.60V
Li03 1.0A 12.60V
Li03 1.0A 12.60V
Li03 1.0A 12.60V
STO 00993 059
STO 00993 059
STO 00993 059
STO 00993 059:
:
:
:51
51
51
51
battery
voltage
number
of cells
charged
capacity
charging
time
charge
current
work
state
Start/Enter
>3 seconds
Batt type
stop
LiPo STORAGE
LiPo STORAGE
LiPo STORAGE
LiPo STORAGE
1.0A 11.1V(3S)
1.0A 11.1V(3S)
1.0A 11.1V(3S)
1.0A 11.1V(3S)
-
Dec
+
Inc
-
Dec
+
Inc
Содержание 1010B
Страница 1: ......