manualshive.com logo in svg

icetro IM-770-AF, Инструкция по установке и обслуживанию

Поделиться
Скачать
icetro IM-770-AF Скачать руководство пользователя страница 8

IM-0770

Sequence Of Operation

8

IM-0770-AN/AF Sequence of Operation

Start-Up Sequence

Power switch set to the “ICE” position:

•

Gear motor, inlet water valve, and bypass valve is energized simultaneously.

•

Bypass valve stays energized for 50 seconds.

•

Bypass valve is de-energizes for 10 seconds.

•

Compressor energizes and freeze cycle begins.

•

Once the head pressure reaches 235 psig, the fan cycle switch closes and the fan motor energizes.

Shut-Down Sequence

Power switch set to the “OFF” position while in freeze:

•

Compressor is de-energizes immediately.

•

Head pressure drops to 175 psig & the fan cycle switch opens, de-energizing the fan motor.

•

Gear motor de-

energizes 1 minutes after the power switch is put in the “OFF” position.

Note: Sump remains full of water.  Dump valve does not energize and drain, so the 
sump remains full of water when the machine is off.

Shut-Down Sequence Via Bin Switch

Same as the previous shut-down sequence:

•

When the bin-switch is made or broken, the machine starts or stops with nearly no delay (2 seconds max).

Purge Cycle (set for every 12 hours)

Total Cycle Time = 20 minutes:

•

Compressor is de-energized.  Dump valve energizes (emptying sump) and the gear motor remains energized.

•

Approximately 5 minutes in, the gear motor is de-energized & the inlet water valve is energized, refilling the 
sump and flooding the evaporator with water.

•

19 minutes in, the dump valve is energized (draining all water).

•

19.5 minutes in, the inlet water valve & gear motor is energized.

•

20 minutes in, the compressor is energized.

•

When head pressure reaches 230 psig, the fan motor is energized

Note: The machine drains & refills 2 times, not continuously.

Содержание IM-770-AF





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды