background image

13

2.18 Fit the mirror

The mirror comes with instructions showing
how it is to be assembled. The mirror is
mounted in the top of one of the handlebars
(right handlebar if you drive on the left, left
handlebar if you drive on the right). A plastic
plug is provided for the opposite handlebar.
Many people prefer to ride with a mirror both
sides.

If you have bar-end shifters, you will have a
mirror mount on the handlebars. Insert the
mirror into the end of the mirror mount and
tighten.

3.1 Adjusting the tracking

The tracking on your trike is pre-adjusted at 
the factory, and should not normally need 
checking. If you experience abnormal tyre 
wear, you will find the instructions for checking 
and adjusting the tracking in the Owner’s 
Manual.

2.19 Fit the flag

Mesh Seat
Place the flag in the flag holder hole in the left 
or right side at the top of the seat frame.

2.20 Reflectors and Bell

Reflectors and a bell are supplied with your 
trike. The bell can be mounted anywhere on 
the handlebars where it can be reached easily 
and doesn’t interfere with steering the trike. The 
reflectors have brackets which allow the front 
reflector to be mounted on the front derailleur 
post, and the rear reflector to be mounted
on the top rail of the seat.

2.21 Check nuts and bolts

Generally, check all nuts, bolts and quick-
releases to make sure everything is tight.

3.0 Other Important Information

3.2 Serial Number

The serial number is marked on the underside 
of the main cross joint.

3.3 Warranty information

New for 2012!. 
Your warranty should be submitted online within 
the first 30 days of ownership.(Information on 
how to activate your warranty can be found 
inside of the front cover). 

Inspired Cycle Engineering warrants, to the 
original owner of each new ICE tricycle that 
the frame, seat, and steering components are 
free of defective materials and workmanship for 
ten (10) years from original date of purchase. 
Component parts are limited to one (1) year 
from original date of purchase. Warranty is 
conditional upon the trike being operated 
under normal conditions and being properly 
maintained. Warranty is offered to the original 
owner only, and is not transferable. This 
warranty does not apply to:

• 

damage through normal wear and tear 

• 

neglect (inadequate care and maintenance) 

• 

damage from crashes or jumping  

• 

overloading through excess weight 

• 

incorrect assembly 

• 

modifications to the trike (additional or 
changed components) 

• 

theft  

• 

use as an non ICE-approved  power driven 
vehicle 

• 

failure to follow instructions or warnings in the 
owner’s manual 

• 

activities for which they were not designed

Bending of frames, handlebars, seats or wheel 
rims can be a sign of misuse or abuse. 

Inspired Cycle Engineering reserves the right 
to make sole determination of whether any 
failure or damage claimed under warranty was 
caused by material or manufacturing defect, and 
reserves the sole discretion to repair or replace 
any parts covered by this warranty. 

The owner shall be responsible for all labour, 
shipping, and travel costs connected with 
the repair or replacement of warranted parts. 
Inspired Cycle Engineering will, at our sole 
discretion, normally consider compensation for 
reasonable labour, shipping, and travel costs 
associated with warranty claims.

Inspired Cycle Engineering shall in no event 
be liable for incidental or consequential losses, 
damages or expenses in connection with its 
tricycle products. 

In practice, if you think you have a warranty 
claim, contact your dealer or us. We are 
passionate about our product, and want you to 
be too. If it is our problem, then we will do our 
best to put it right.

Hardshell
Place the flag in the flag holder hole in the left 
or right side at the top of the seat frame.

Содержание Trike 2012
















Отзывы: