13
Rev. 2
Alarm Operation
1.
The enclosure temperature is above or below the alarm set-point:
The “Alarm” LED will light, the display will flash, the “HI” or the “LO” LED will flash, and the
audible alarm sounds (if activated.) The enclosure temperature must rise or fall 2°F (1°C) before
the alarm will reset.
2.
The condenser temperature is above the condenser alarm set-point:
The “Alarm” LED lights, the display flashes the condenser temperature, and the audible alarm
sounds (if activated.) the condenser temperature must fall 4°F (2°C) before the alarm will reset.
The above alarms can be manually reset by entering the PIN code into the system.
3.
The filter day timer has expired:
The “Alarm” LED lights, the display flashes “FIL”, the “Filter” LED flashes with the display and
the audible alarm sounds (if activated.) The filter alarm may be cleared by pressing
“4 Exit”.
4.
The power is turned off:
The “Alarm” LED lights, and the display flashes “OFF” indicating someone has manually
interrupted power to the motors’ electrical circuits. This alarm will be rest when the Por “ON” has
been selected in the program menu.
(Version 3.18 and later only)
5.
Optional Alarm Output:
Ice Qube offers an optional dry contact alarm output (XO3) that provides both a normally open
(close on alarm) and a normally closed (open on alarm) set of contacts. This alarm signal is
provided from a relay through a 3 conductor cable
(Black/Common, White/Normally Open, and
Red/Normally Closed)
passing through a strain relief to the left of the internal controller.
6.
Sensor Malfunctions:
E-O:
Evaporator
sensor
open
E-C:
Evaporator
sensor
shorted
C-O:
Condenser
sensor
open
C-C:
Condenser
sensor
shorted
Alternating E-O and C-O:
Sensor connector disconnected
7.
Incorrect Voltage Supply:
A continual flashing value of the program version (“3.1x” where x indicates current program
version) on the display screen indicates the supply voltage is either too high or too low.
Содержание 1IQ0000EVZ2
