12
Rev. 2
Press
“3”
to continue. The “Alarm” LED will flash and the display will show “ALL” indicating the “ALL”
alarm on/off status. Press
“3”
and the display will show either “ON” or “OFF”, indicating current alarm
status. Press
“1”
or
“2”
to toggle the mode as desired. If the “OFF” mode is selected, no alarms will
activate and the audible on/off select and POA, Power Off Alarm, functions are skipped.
Press
“3”
to continue. The “Audible” LED will flash and the display will show “AUD”, indicating the
audible alarm on/off status. Press
“3”
and the display shows “ON” or “OFF” indicating the current audible
alarm status. Press
“1”
or
“2”
to toggle the mode desired.
Press
“3”
to continue. The “Alarm” LED will flash and the display will show “POA”, indicating the Power
Off Alarm status. Press
“3”
and the display shows “ON” or “OFF” indicating the current alarm status.
Press
“1”
or
“2”
to toggle the mode desired.
(Version 3.18 and later only)
Press
“3”
to continue. The “C” LED will flash and the display will show either “F” for degrees Fahrenheit
or “C” for degrees Celsius. Press
“1”
or
“2”
to toggle the mode desired.
Press
“3”
to continue. The “Code” LED will flash and the display will show “PIN”. To set a new user PIN
code, press
“1”
. The display will flash “4”, prompting an entry of a four button sequence using the
“1”,
“2”, “3,
and/or
“4”
buttons. Any sequence of the four buttons may be programmed as the code. As the
buttons are pressed, the display will show the number of buttons that were pressed.
Note: After pressing a button, there will only be 5 seconds to press the next button. If the next button is
not pressed within the allotted time, the system will default to no PIN code, indicated by “0” on the
display. Once the sequence is entered the display will no longer flash, and will show “4”.
To program the no PIN code mode, press
“2”
and the display will show “0”, indicating no PIN code. With
no PIN code, pressing any button will permit access to the program.
•••CAUTION•••
ALWAYS RECORD THE SELECTION SEQUENCE (PIN CODE) AND STORE IN A SECURE PLACE
Press
“3”
to continue. The “filter” LED flashes and the display will show “FIL”, indicating the filter alarm
day quantity selection. Press
“3”
and the display will show the number of days that the alarm is set in half
day increments. Note that the alarm is based on compressor run time. (Example: 10.5 indicates that the
alarm will activate every ten and a half days or 252 hours of compressor run time.)
Press
“1”
or
“2”
to vary the desired number of days. Programming “0” days will disable the alarm.
Note: The required number of days to set this alarm will be determined by the ambient air conditions.
Programming of the microprocessor is now complete. Press
“3”
to review all of the settings. Press
“4”
to
enter the selected settings and to return to the normal operating mode.
Note: if “4” is not pressed, any changes to the program settings will not be saved.
Содержание 1IQ0000EVZ2
