Ice-O-Matic GEM0650A/W Скачать руководство пользователя

Страница: 3 / 43

GEM0650/0956/1256 A/W

Forward

Page i

How To Use This Manual

ICE-O-Matic provides this manual as an aid to the end user and service technician in installation and

maintenance of the

GEM Series

ice machines. Do not attempt to perform installation, start-up or maintenance

unless you have read and fully understand this manual.

If, at any time, you encounter conditions that are not addressed in this manual, call, E-mail or write the ICE-O-

Matic Service Department:

ICE-O-Matic

11100 E. 45

Ave.

Denver, Co. 80239

Attn: Technical Service Department

E-Mail: [email protected]

Telephone Numbers

Any Service communication must include:

800-423-3367 All

Departments

•

Model Number

888-349-4423 Technical Assistance Only

•

Serial number

303-371-3737

•

A detailed explanation of the problem

Keep this manual for future reference.

The GEM0650A/W, GEM0956A/W and GEM1256A/W Series Service Parts Manuals are available separately.

ICE-O-Matic icemakers and dispensers are not approved for outdoor installation.

WARNING: Always disconnect electrical power and shut off water supply whenever maintenance or

repairs are performed on the ice machine and related equipment.

CAUTION: Always wear protective eyewear whenever maintenance or repairs are performed on the ice

machine and related equipment

Содержание GEM0650A/W












































Результаты поиска

Содержание GEM0650A/W

Отзывы:

Похожие инструкции для GEM0650A/W

Бренды по названию

Популярные бренды

Ice-O-Matic GEM0650A/W, Руководство по обслуживанию и установке

Результаты поиска

Содержание GEM0650A/W

Отзывы:

Похожие инструкции для GEM0650A/W

Бренды по названию

Популярные бренды