Model VIP+
3
Owner's Manual
Technical Specifications
Material
The Model VIP+ double wall vent is constructed of either stainless steel grade 304 or 316 for the flue and stainless steel grade 304 or 316 or
Galvalume for the casing. When required, the vent is insulated with high temperature mineral fiber insulation. Proper joint sealant or gasket material
is provided as per venting application (Low Temp or High Temp).
Weight / Standard Thickness
Table 1 - Standard Thickness and Chimney Weight
Ø
6
8
10
12
14
16
18
20
22
24
VIP+
1” Air
Insulated
Flue Thickness
0.019"
0.025"
Casing Thickness
0.019"
0.025"
Weight (lbs / ft)
3.3
4.2
5.1
6.0
6.9
7.9
9.9
11.0
12.0
13.1
VIP+
1” Fiber
Flue Thickness
0.019"
0.025"
Casing Thickness
0.019"
0.025"
Weight (lbs / ft)
4.4
5.6
6.9
8.1
9.3
10.6
13.0
14.4
15.7
17.1
VIP+
2” Fiber
Flue Thickness
0.019"
0.025"
Casing Thickness
0.019"
0.025"
Weight (lbs / ft)
6.4
8.0
9.5
11.1
12.6
14.0
17.0
18.7
20.4
22.1
VIP+
4” Fiber
Flue Thickness
0.019"
0.025"
Casing Thickness
0.019"
0.025"
Weight (lbs / ft)
11.3
13.5
15.7
18.0
20.2
22.4
26.0
28.3
30.2
33.5
On request, model VIP+ Venting System can be built using thicker gauge material. Contact Factory for weight specifications with non-standard thickness
Venting Applications
Building Heating Appliance (BHA) Chimney (UL 103 Listing) :
Under this category, model VIP+ has been determined suitable for venting flue gases at temperatures not exceeding 538°C (1000°F) under
continuous operating conditions from gas, liquid, oil or solid fuel fired appliances. Also complies with operation (less than one hour) at temperatures
not exceeding 760°C (1400°F) and brief operation (maximum 10 minutes) at temperatures not exceeding 927°C (1700°F).
Building Heating Appliance Chimneys are suitable for use with Building Heating Appliances and Low Heat Appliances as described in the Chimney
Selection Chart of National Fire Protection Association (NFPA) Standard NO. 211.
1400°F Chimney (UL 2561 Listing) :
Under this category, model VIP+ has been determined suitable for venting flue gases at temperatures not exceeding 760°C (1400°F) under
continuous operating conditions from gas, liquid, oil or solid fuel fired appliances. Also complies with brief operation (maximum 10 minutes)at
temperatures not exceeding 980°C (1800°F). As such, it is suitable for use with ovens and furnaces as described in the Chimney Selection Chart of
NFPA No. 211, in addition to other applications.
Positive Pressure Listing (UL 103 and UL 2561) :
Model VIP+ has been determined suitable for use at a maximum of 60 inch water column internal pressure.
540°C and 760°C Industrial Chimneys (ULC C-959 Listing) :
Under this category, model VIP+ has been determined suitable for venting flue gases at temperatures not exceeding 760°C (1400°F) under
continuous operating conditions from gas, liquid or oil fired appliances. Also complies with brief operation (maximum 10 minutes) at temperatures not
exceeding 980°C (1800°F).
Surroundings / Enclosure
ICC Model VIP+ chimney is primarily intended to be used in fire resistive non-combustible surroundings or installed unenclosed. They are not
intended for use in one or two family residences.
Содержание VIP+ Air Insulated
Страница 23: ...Model VIP 23 Owner s Manual Figure 36...
Страница 24: ...Model VIP 24 Owner s Manual Figure 37...
