ICC Mirius Скачать руководство пользователя | Manualshive

Страница: 21 / 56

background image

21

BACnet / Gas Water Heaters

Table 12. Xi 1.0 Energy Management System (EMS) Control

Decimal

Hex

Value

Response

3840

0x0F00 No EMS control

0 / 0x000

3841

0x0F01 Put into EMS Mode^

49152 / 0xC000

0000

0x0000 EMS Disable heating^

49152 / 0xC000

0001

0x0001 EMS Enable heating^

49153 / 0xC001

3584

0x0E00 EMS Mode Refresh^ (must write within 30 seconds

or EMS mode ends.) 15 seconds or less

recommended

49152 / 0xC000 or 49153 / 0xC001 depending on

whether or not heating is enabled.

Notes:

The start of a heating also depend on other factors like tank temperature dropping below Setpoint – Differential and External T’stat call for heat if that option is enabled.

Depending on when you poll the register, you may read bit 14 as 1 which is why a “C” (in hexadecimal form) might brieﬂy reply with “8”. This is due to the control setting

this bit and if it not cleared periodically by the BACnet command, heating is disabled.

After disabling EMS mode with write of 3840, read back might have bits 14 and 1 possibly still set. To make sure these bits are clear, write a 0000 to clear bit 1 and 3584 to

clear bit 14.

Mxi Energy Management System (EMS) Control

Mxi EMS control is written as a single command to place in EMS mode and enable or disable heating.
Once in EMS mode the EMS Mode Refresh command must be periodically issued to maintain EMS mode, otherwise the heater will end

EMS mode and resume normal operation.

Table 13. Mxi Energy Management System (EMS) Control

Decimal

Hex

Value

Response

0

0x0000

No EMS control~

0 / 0x000

32768

0x8000

EMS Disable Heating^

49152 / 0xC000

32769

0x8001

EMS Enable Heating^*

49153 / 0xC001

Notes:

~ For Versions less than 3.16, once EMS control mode is enabled it remains enabled through BACnet it will remain in EMS control mode that cannot be cleared by writing

a 0 to it. Power cycling only can clear EMS mode.

^ Depending on when you poll the register, you may read bit 14 as 1 which is why a “C” (in hexadecimal form) might brieﬂy reply with “8”. This is due to the control setting

this bit and if it not cleared periodically by the BACnet command, heating is disabled.

* EMS command to heat must be sent every 30 maximum or heating will be disabled.

«
...
19
20
21
22
23
...
»

Содержание Mirius

























































Отзывы:

Нет отзывов

Похожие инструкции для Mirius

Бренд: Net2Phone Страницы: 23

Бренд: Eaton Страницы: 2

Бренд: CastleNet Страницы: 29

Бренд: Edimax Страницы: 27

Бренд: SAGEMCOM Страницы: 60

Бренд: RTA Страницы: 88

M2M CONTROL C660

Бренд: Infranet Technologies Страницы: 36

Бренд: SAFARI Страницы: 8

Бренд: ICP DAS USA Страницы: 24

Intelligent Gateway 1800

Бренд: 2Wire Страницы: 148

Бренд: Planet Networking & Communication Страницы: 2

Бренд: Cradlepoint Страницы: 148

Бренд: Daikin Страницы: 44

hotspot gateway

Бренд: Jaze Страницы: 102

Бренд: Arris Страницы: 116

Бренд: ACT'L Страницы: 38

Бренд: RTA Страницы: 66

Бренд: Gainwise Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды