IBM Storwize V5100 Series Скачать руководство пользователя страница 80

Страница: 80 / 130

Figure 66. Fibre Channel adapters in the node canisters

2. To connect additional Fibre Channel cables, connect the same number of cables to each canister.

Connecting optional expansion enclosures to the control enclosure

If you have installed expansion enclosures in the rack, you must connect them to the control enclosure.

About this task
This task applies if you are installing one or more expansion enclosures. Each control enclosure in the

system can manage two chains of expansion enclosures; each chain can consist of a maximum of 10 2U

expansion enclosures. Therefore, each control enclosure can support up to 20U of expansion enclosures.

A system that contains two control enclosures can support up to 40U of expansion enclosures.
Note: When connecting SAS cables between enclosures, you must follow a list of guidelines to ensure

that your configuration is valid. Do not begin connecting the cables until you have read Figure 67 on page

57.

Procedure
To install the cables, complete the following steps.

1. Using the supplied SAS cables, connect the control enclosure to the expansion enclosure at rack

position 1, as shown in Figure 67 on page 57.

a) Connect SAS port 1 of the upper node canister in the control enclosure to SAS port 1 of the left

expansion canister in the first expansion enclosure.

b) Connect SAS port 1 of the lower node canister in the control enclosure to SAS port 1 of the right

expansion canister in the first expansion enclosure.

56 Storwize V5100 : Quick Installation Guide for MTM 2078-424, 2078-12F, 2078-24F, 2078-92F, and 2078-

U5B

Содержание Storwize V5100 Series



































































































































Результаты поиска

Содержание Storwize V5100 Series

Отзывы:

Похожие инструкции для Storwize V5100 Series

Бренды по названию

Популярные бренды

IBM Storwize V5100 Series, Быстрое руководство по установке

Результаты поиска

Содержание Storwize V5100 Series

Отзывы:

Похожие инструкции для Storwize V5100 Series

Бренды по названию

Популярные бренды