background image

Racks with a total weight of > 227 kg (500 lb.), Use Only Professional Movers!
(R003)

DANGER

Do not transport the rack via fork truck unless it is properly packaged,
secured on top of the supplied pallet. (R004)

DANGER

Main Protective Earth (Ground):

This symbol is marked on the frame of the rack.

The PROTECTIVE EARTHING CONDUCTORS should be terminated at that
point. A recognized or certified closed loop connector (ring terminal) should
be used and secured to the frame with a lock washer using a bolt or stud.
The connector should be properly sized to be suitable for the bolt or stud, the
locking washer, the rating for the conducting wire used, and the considered
rating of the breaker. The intent is to ensure the frame is electrically bonded
to the PROTECTIVE EARTHING CONDUCTORS. The hole that the bolt or
stud goes into where the terminal conductor and the lock washer contact
should be free of any non-conductive material to allow for metal to metal
contact. All PROTECTIVE EARTHING CONDUCTORS should terminate at

this main protective earthing terminal or at points marked with 

. (R010)

Special caution and safety notices

This information describes special safety notices that apply to the Storwize V3500.
These notices are in addition to the standard safety notices supplied and address
specific issues relevant to the equipment provided.

General safety

When you service the Storwize V3500, follow general safety guidelines.

Use the following general rules to ensure safety to yourself and others.

v

Observe good housekeeping in the area where the devices are kept during and
after maintenance.

v

Follow the guidelines when lifting any heavy object:

1.

Ensure that you can stand safely without slipping.

2.

Distribute the weight of the object equally between your feet.

3.

Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.

4.

Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any objects that
weigh more than 18 kg (40 lb) or objects that you think are too heavy for you.

v

Do not perform any action that causes a hazard or makes the equipment unsafe.

xiv

Storwize V3500: Quick Installation Guide

Содержание Storwize V3500















































































Отзывы: