IBM Power Systems Series Скачать руководство пользователя страница 23

Страница: 23 / 134

8. To determine the command to type on the Petitboot command line to verify that the drives that are

known to be in a RAID array are recognized, use Table 2 on page 9.

Table 2. Determine the command to verify that the drives that are known to be in a RAID array are

recognized
Drive configuration

Commands

Drive connected directly to the system

backplane

•

arcconf getconfig 1 LD

•

arcconf getconfig 1 PD

Are the drives that are known to be in the RAID array recognized?

Then

Yes:

Reinstall the operating system on the boot drive. This ends the procedure.

No:

Continue with the next step.

9. Complete the following actions, one at a time until the physical drives are recognized in the RAID

array:
Note:
• If your system is a 5104-22C or 9006-22C, go to “5104-22C or 9006-22C locations” on page 63

to identify the physical location and the removal and replacement procedure.

• If your system is a 9006-12P, go to “9006-12P locations” on page 75 to identify the physical

location and the removal and replacement procedure.

• If your system is a 9006-22P, go to “9006-22P locations” on page 91 to identify the physical

location and the removal and replacement procedure.

a. If the drive is connected directly to the system backplane, ensure that the mini-SAS cable and

SATA cables are properly seated in the disk drive backplane and system backplane.

b. Replace the SAS or SATA cable.

c. If the drive is connected directly to the system backplane, replace the system backplane.

This ends the procedure.

10. Does an operating system error occur during the boot?

Then

Yes:

Recover the operating system with the tools for the operating system. If that does

not resolve the problem, reinstall the operating system. This ends the procedure.

No:

Reinstall the operating system. This ends the procedure.

Resolving a sensor indicator problem

Learn how to resolve a sensor indicator problem.

About this task
To determine whether a service action is required, complete the following procedure:
Note: For more information about sensors, see Sensor readings GUI display.

Procedure

1. If the system is not powered on, boot the system to the operational state. Log in to the BMC web

interface. Then, click Server Health > Sensor Readings.
Are any of the sensor indicator LEDs red?

Beginning troubleshooting and problem analysis 9

Содержание Power Systems Series







































































































































Результаты поиска

Содержание Power Systems Series

Отзывы:

Похожие инструкции для Power Systems Series

Бренды по названию

Популярные бренды

IBM Power Systems Series, Анализ проблем, составные части системы и расположение

Результаты поиска

Содержание Power Systems Series

Отзывы:

Похожие инструкции для Power Systems Series

Бренды по названию

Популярные бренды