IBM AS/400e Скачать руководство пользователя страница 57

Страница: 57 / 85

__ 18.

The green light stops blinking and remains on solid when you installed
disk unit properly.

__ 19.

Return to the console and wait until the Concurrent Maintenance Results
display appears.
Press the Enter key.

__ 20.

Do you have more disk units to install?

Yes

↓

Repeat steps 5 on page 44 through 19.

__ 21.

When the Hardware Service Manager display appears, press F12.

__ 22.

On the System Service Tool display, select Work with Disk Units.
Press the Enter key.

__ 23.

On the Work with Disk Units display, select Display disk configuration.
Press the Enter key.

__ 24.

On the Display disk configuration display, select Display non-configured
units.
Press the Enter key.

__ 25.

The display should list the disk unit that you installed. The serial number
should match the serial number you wrote in step 12 on page 44.

Note:

If the display does not list the disk unit, ensure that you properly
installed the disk unit. Repeat steps 1 on page 43 through 19.

__ 26.

Press F12, twice.

__ 27.

On the Work with disk units display, select Work with disk configuration.
Press the Enter key.

__ 28.

Are you adding a disk unit to an existing device parity set? If you need
more information about device parity, go to the

Backup and Recovery

SC41-5304-04 .

Figure 36. Installing a disk unit

Appendix C. Installing disk units in the 5065 or 5066 Expansion Unit

Содержание AS/400e






















































































Результаты поиска

Содержание AS/400e

Отзывы:

Похожие инструкции для AS/400e

Бренды по названию

Популярные бренды

IBM AS/400e, Руководство пользователя

Результаты поиска

Содержание AS/400e

Отзывы:

Похожие инструкции для AS/400e

Бренды по названию

Популярные бренды