IBM 86594RY - Netfinity 5000 - 4RY Скачать руководство пользователя страница 110

Страница: 110 / 220

Installing the rack model in a rack
enclosure:

During this procedure, you must install

parts on the rack enclosure and the server. This process
can be divided into three parts:

Preparing the server

Preparing the rack enclosure

Installing the server into the rack enclosure

Before you begin

Read “Safety information” on page 176 and the
safety information in the rack enclosure
documentation.

Turn off the server, if it is on.

Refer to the rack enclosure documentation for
additional information on preparing the rack.

Preparing the server:

In this section, you will use the

following parts:

One cable arm bracket

The inner slide from two slide bracket assemblies

6 pan-head short screws (M4 by 5 mm)

Caution

Use safe lifting practices when lifting the machine.

Attention

To avoid damage to internal components, use only the
pan-head short screws (M4 by 5 mm) included with
the Rack Mount Kit.

32 kg (70.5 lbs)

55 kg (121.2 lbs)

102

Netfinity Server HMM

Содержание 86594RY - Netfinity 5000 - 4RY





























































































































































































































Результаты поиска

Содержание 86594RY - Netfinity 5000 - 4RY

Отзывы:

Похожие инструкции для 86594RY - Netfinity 5000 - 4RY

Бренды по названию

Популярные бренды

IBM 86594RY - Netfinity 5000 - 4RY, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 86594RY - Netfinity 5000 - 4RY

Отзывы:

Похожие инструкции для 86594RY - Netfinity 5000 - 4RY

Бренды по названию

Популярные бренды