IBM 7380E1U, Инструкция по установке и эксплуатации

Страница: 23 / 160

Table 1. Features and specifications (continued)
Integrated functions:
v Integrated Management Module (IMM),
which provides service processor
control and monitoring functions, video
controller, remote keyboard, video,
mouse, and remote hard disk drive
capabilities
v
Dedicated or shared management
network connections
v
Six-port Serial ATA (SATA) controller
embedded
v
Serial over LAN (SOL) and serial
redirection over Telnet or Secure Shell
(SSH)
v
USB flash device with embedded
hypervisor software.
v
Support for remote management
presence
v
One systems-management RJ-45 for
connection to a dedicated
systems-management network. This
system management connector is
dedicated to the IMM functions.
v Light path diagnostics
v Six Universal Serial Bus (USB) ports
standard (v2.0 supporting v1.1)
– Four on rear of server
– Two on front of server
v One internal USB tape connector
v One Broadcom dual-port 10/100/1000
Ethernet controller with Wake on LAN
support and TCP/IP Offload Engine
(TOE) support
v One serial connector, shared with the
IMM
Note: In messages and documentation,
the term service processor refers to the
integrated management module (IMM).
Video controller:
v
Matrox G200eV video on system board
v Compatible with SVGA and VGA
ServeRAID SAS adapter:
v
ServeRAID-BR10i SAS/SATA adapter
that supports RAID levels 0, 1, 1E
(standard)
v ServeRAID-BR10il SAS/SATA adapter
that supports RAID levels 0, 1, 1E
(standard)
v Optional ServeRAID-MR10i SAS/SATA
adapter, which supports RAID levels 0,
1, 5, 6, 10
v
Optional ServeRAID-MR10is
SAS/SATA adapter, which supports
RAID levels 0, 1, 5, 6, 10
v Optional ServeRAID-M1015 SAS/SATA
adapter, which supports RAID level 0,
1, 1E
v
Optional ServeRAID-M5014 SAS/SATA
adapter, which supports RAID level 0,
1, 5, 10, 50
v
Optional ServeRAID-M5015 SAS/SATA
adapter, which supports RAID level 0,
1, 5, 10, 50
Note: If the server is configured for
RAID operation using a ServeRAID
adapter, you might have to reconfigure
your disk arrays after you install
drives. See the ServeRAID adapter
documentation for additional
information about RAID operation and
complete instructions for using the
ServeRAID adapter.
Acoustical noise emissions:
v
Sound power, idle: 5.5 bel declared
v
Sound power, operating: 6.0 bel
declared
Environment:
v Air temperature:
– Server on: 10°C to 35°C (50.0°F to
95.0°F); altitude: 0 to 915 m (3000
ft)
– Server on: 10°C to 32°C (50.0°F to
90.0°F); altitude: 915 m (3000 ft) to
2134 m (7000 ft)
– Server on: 10°C to 28°C (50.0°F to
83.0°F); altitude: 2134 m (7000 ft)
to 3050 m (10000 ft)
– Server off: 5°C to 45°C (41°F to
113°F)
– Shipping: -40°C to 60°C (-40.0°F to
140°F)
Humidity:
v Server on: 20% to 80%, maximum dew
point 21°C, maximum rate of change
5°C/hour
v Server off: 8% to 80%, maximum dew
point 27°C
Heat output:
Approximate heat output:
v
Minimum configuration: 2013 Btu per
hour (590 watts)
v
Maximum configuration: 3610 Btu per
hour (1058 watts)
Electrical input:
v Sine-wave input (50-60 Hz) required
v Input voltage low range:
– Minimum: 100 V AC
– Maximum: 127 V AC
v Input voltage high range:
– Minimum: 200 V AC
– Maximum: 240 V AC
v
Approximate input kilovolt-amperes
(kVA):
– Minimum: 0.60 kVA
– Maximum: 1.10 kVA
Notes:
1. Power consumption and heat output
vary depending on the number and type
of optional features that are installed
and the power-management optional
features that are in use.
2. These levels were measured in
controlled acoustical environments
according to the procedures that are
specified by the American National
Standards Institute (ANSI) S12.10 and
ISO 7779 and are reported in
accordance with ISO 9296. Actual
sound-pressure levels in a given
location might exceed the average
stated values because of room
reflections and other nearby noise
sources. The declared sound-power
levels indicate an upper limit, below
which a large number of computers will
operate.
Chapter 1. The System x3500 M3 server
7