background image

• Connect all devices installed in a rack cabinet to power devices installed in the same rack

cabinet. Do not plug a power cord from a device installed in one rack cabinet into a power device

installed in a different rack cabinet.

• An electrical outlet that is not correctly wired could place hazardous voltage on the metal parts

of the system or the devices that attach to the system. It is the responsibility of the customer to

ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (R001 part

1 of 2)

(R001 part 2 of 2):

CAUTION:
• Do not install a unit in a rack where the internal rack ambient temperatures will exceed the

manufacturer's recommended ambient temperature for all your rack-mounted devices.

• Do not install a unit in a rack where the air flow is compromised. Ensure that air flow is not

blocked or reduced on any side, front, or back of a unit used for air flow through the unit.

• Consideration should be given to the connection of the equipment to the supply circuit so that

overloading of the circuits does not compromise the supply wiring or overcurrent protection. To

provide the correct power connection to a rack, refer to the rating labels located on the

equipment in the rack to determine the total power requirement of the supply circuit.

• (For sliding drawers.) Do not pull out or install any drawer or feature if the rack stabilizer brackets

are not attached to the rack or if the rack is not bolted to the floor. Do not pull out more than one

drawer at a time. The rack might become unstable if you pull out more than one drawer at a time.

• (For fixed drawers.) This drawer is a fixed drawer and must not be moved for servicing unless

specified by the manufacturer. Attempting to move the drawer partially or completely out of the

rack might cause the rack to become unstable or cause the drawer to fall out of the rack. (R001

part 2 of 2)

Procedure

1. If you are installing a new feature, ensure that you have the software that is required to support the

new feature. See IBM Prerequisite.

2. If you are installing or replacing something that might put your data at risk, ensure, wherever possible,

that you have a current backup of your system or logical partition (including operating systems,

licensed programs, and data).

3. Review the installation or replacement procedure for the feature or part.
4. Note the significance of color on your system.

Blue or terra-cotta on a part of the hardware indicates a touch point where you can grip the hardware

to remove it from or install it in the system, or open or close a latch. Terra-cotta might also indicate

that the part can be removed and replaced with the system or logical partition powered on.

5. Ensure that you have access to a medium flat-blade screwdriver, a Phillips screwdriver, and a pair of

scissors.

6. If parts are incorrect, missing, or visibly damaged, do the following steps:

• If you are replacing a part, contact the provider of your parts or next level of support.
• If you are installing a feature, contact one of the following service organizations:

– The provider of your parts or next level of support.

Common procedures for servicing or installing features in the 5104-22C, 9006-22C, or 9006-22P system  101

Содержание 5104-22C





















































































































































Отзывы: