IBM 5000XHV Скачать руководство пользователя

Страница: 1 / 14

5000XHV

NINTERRUPTIBLE

OWER

UPPLY

UICK

NSTALLATION

UIDE

46M5391

1: O

VERVIEW

TTENTION

•

Read the Safety Instructions before installing the uninterruptible power supply.

•

The uninterruptible power supply and battery modules are heavy. Select a location sturdy enough to handle the weight.

•

Refer to the

Uninterruptible Power Supply Operation and Setup Guide

for information on how to obtain service and support for the

unit.

OTE

Illustrations in this document might vary in appearance from the purchased unit.

•

Utility knife or scissors

•

Two Phillips screwdrivers (#1 and #2)

•

One wrench (10mm)

•

Cage nut insertion tool or flat-blade screwdriver (for installing cage nuts in some rack cabinets)

Inventory

Quick Installation Guide

Important Notices Flyer

Documentation

Warranty Flyer

PowerChute



Business Edition
software CD

Network Management Card documentation CD

Содержание 5000XHV















Результаты поиска

Содержание 5000XHV

Отзывы:

Похожие инструкции для 5000XHV

Бренды по названию

Популярные бренды

IBM 5000XHV, Быстрое руководство по установке

Результаты поиска

Содержание 5000XHV

Отзывы:

Похожие инструкции для 5000XHV

Бренды по названию

Популярные бренды