IBM 4002-C2A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 98

background image

Product documents

The following documents contain information related to this product. The
documentation may be printed material or may be on the documentation CD that
is shipped with the product. Newer versions of product documentation may be
available through the IBM Publications Center Web site www.ibm.com/shop/
publications/order or through the IBM Systems Networking Support Web site
www.ibm.com/systems/support/networking. Search by product, publication title,
or publication number.

v

IBM Ethernet Switch Installation and User Guide

, GC27-2238-01

v

IBM Systems Safety Notices

, G229–9054

v

IBM Systems Environmental Notices and User Guide

, Z125-5823

v

IBM Warranty

Software documents

IBM Ethernet switch and router products use software licensed from Brocade
Communications Systems, Inc. You can find software publications that support
your product on the CD-ROM supplied with this product.

The software publications associated with this product are:

v

NetIron Configuration Guide

v

IronWare MIB Reference

These software publications reflect only the original Brocade products names. Use
the cross-reference of products in Table 1 to assist you when determining which
information in those publications applies to your product. Brocade products with
no IBM equivalents are not listed in the table. Note that the IBM products can be
ordered with additional features, while Brocade products with those additional
features may be offered as separate models.

Table 1. Comparable IBM and Brocade products.

IBM
product
name

IBM
mach
-ine
type

IBM model
(HVEC/XCC
model in
parentheses)

Brief product description

Brocade product name

Brocade product
part number

Ethernet
Router
B04M

4003

M04

4U modular Ethernet router
with 4 interface slots

NetIron MLX-4

NI-MLX-4-AC

Ethernet
Router
B08M

4003

M08

7U modular Ethernet router
with 8 interface slots

NetIron MLX-8

NI-MLX-8-AC

Ethernet
Router
B16M

4003

M16

14U modular Ethernet router
with 16 interface slots

NetIron MLX-16

NI-MLX-16-AC

Ethernet
Router
B32M

4003

M32

33U modular Ethernet and IP
router with 32 interface slots

NetIron MLX-32

NI-MLX-32-
AC-A

Ethernet
Switch B04R

4003

R04

4U modular Ethernet switch
with 4 interface slots

BigIron RX-4

BI-RX-4-AC

Ethernet
Switch B08R

4003

R08

7U modular Ethernet switch
with 8 interface slots

BigIron RX-8

BI-RX-8-AC

xx

IBM Ethernet Switch c-series Installation and User Guide

«
...
20
21
22
23
24
...
»

Содержание 4002-C2A



































































































Отзывы:

Нет отзывов

Похожие инструкции для 4002-C2A

Hard Disk MAX Quadra

Бренд: LaCie Страницы: 2

8BIG RACK THUNDERBOLT 2

Бренд: LaCie Страницы: 28

Бренд: Husky Страницы: 10

Бренд: Jefferson Страницы: 2

Бренд: BOH Enviromental Страницы: 20

2big Thunderbolt

Бренд: LaCie Страницы: 72

Бренд: Fast Mover Страницы: 2

Бренд: Frontier Страницы: 6

Бренд: LaCie Страницы: 26

Бренд: Oracle Страницы: 268

Бренд: Metro DataVac Страницы: 16

EonStor DS B Series

Бренд: Infotrend Страницы: 157

Бренд: Dancover Страницы: 30

Бренд: SATA Страницы: 44

Бренд: Seagate Страницы: 27

Бренд: LaCie Страницы: 26

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды