IBM 342 7208 Скачать руководство пользователя страница 58

Страница: 58 / 92

3.13 Step 11

This step describes the reassembly process.

1. Press the power switch to turn off the power.

2. Unplug the power cable from the electrical outlet.

3. Make sure that the power supply connector (J1) is plugged into the drive.

4. Make sure that the power supply connector (J2) is plugged into the cooling fan.

5. Make sure that all other cables are properly connected, and that the wires are routed away from the cooling fan.

6. Perform the cover replacement procedure. Refer to "Removing and Replacing the Cover" in topic 4.2.

7. Plug the power cable into the electrical outlet.

8. Press the power switch to turn on the power.

Does the power-on light come and stay on, and is there airflow from the fan?

NO Verify that the 7208 Tape Drive was reassembled correctly. If the power-on light still does not come on and there is no airflow

from the fan, go to Step 1.

YES Go to Step 12.

7208 Tape Drive Service Guide

Step 11

¦ Copyright IBM Corp. 1998

3.13 - 1

Содержание 342 7208





























































































Результаты поиска

Содержание 342 7208

Отзывы:

Похожие инструкции для 342 7208

Бренды по названию

Популярные бренды

IBM 342 7208, Руководство по обслуживанию

Результаты поиска

Содержание 342 7208

Отзывы:

Похожие инструкции для 342 7208

Бренды по названию

Популярные бренды