background image

 

13 

 

TRANSPORT 

Except when working, moving the machine takes place when the machine is standing still and the transmission 
is disconnected. 
<

Important

>: keep speed low avoiding holes and ground roughness. 

<

Note

> when on the road, obey existing traffic laws. Exhibit the signal signs on the rear ends. Respect any 

local laws there may be.  
<

Note

> Lock the lifting bars of the tractor with the chain and tightners. They must be parallel to the bars. 

 

STORAGE 

Store the machine in a dry place that isn't dusty. 

 

 
 

INFORMATION ON DEMOLITION 

 At the end of its working life, the machine must be sent to be demolished and that can only be done by 

an authorized authority, in accordance with the national laws in force for the environment. Therefore it is 
necessary to get information from the qualified local authorities on the procedure to follow. The machine is 
mainly composed of: iron materials and paints. 

 

WARRANTY 

 

The machine is covered by the manufacturer warranty for a period of 24 months. 
The warranty is not applicable when: 

 

a)  The maintenance work has not been done correctly. 
 
b)  The machine has been used out of its own service. 
 
c)  The machine has been transformed or modified without the manufacturer's written authorization.

 

 

 

 

Содержание TX40



























Отзывы: