iBell Tools IBL ID 13-80 Скачать руководство пользователя

Страница: 19 / 20

Suspected malfunctions are often due to causes that the users can
fix themselves, therefore check the product using this section. In
most cases the problem can be solved quickly.

Problem

Possible Cause

Solution

1. Product does
not start

1.1 No power supply
1.2 Product damaged

1.3 Other electrical
      defect to the
      product

1.1 Check the plug on
      the power supply
1.2 Check it by an
      electrician
1.3 Check it by an
      electrician

2. Unsatisfactory
result

2.1 Drill bit is worn
2.2 Drill bit not
      suitable for
      intended operation

2.1 Replace with a new
one
2.2 Use suitable driver
bit

3. Product
suddenly
stops

3.1 Product overloaded

3.1 Remove the
      product from
      the work-piece and
      switch it on again

TROUBLESHOOTING

WARNING!

Only perform the steps described within these

instructions! All further inspection, maintenance and repair work must

be performed by an authorised service centre or a similarly qualified

specialist if you cannot solve the problem yourself!

IBL ID13-80|TD13-100

Содержание IBL ID 13-80





















Результаты поиска

Содержание IBL ID 13-80

Отзывы:

Похожие инструкции для IBL ID 13-80

Бренды по названию

Популярные бренды

iBell Tools IBL ID 13-80, Руководство оператора

Результаты поиска

Содержание IBL ID 13-80

Отзывы:

Похожие инструкции для IBL ID 13-80

Бренды по названию

Популярные бренды