background image

4

MANUFACTURER´S DECLARATION
DECLARATION OF CONFORMITY

Manufacturer

IBC control AB

Brännerigatan 5 A

SE-263 37 Höganäs

Sweden

Tel: +46 42 33 00 10

Product

Control unit for rotary heat exchanger

Type designation

MicroMax750

Applicable  

EU Directives

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

RoHS Directive 2011/65/EU including Delegated Directive EU2015/863

Applicable  

UK Directives

The Electromagnetic Compatibility Regulations 2016 

The Electrical Equipment (Safety) Regulations 2016 

The Restriction of the Use of Certain Hazardous Substances in Electrical and 

Electronic Equipment Regulations 2012

Harmonizing  

standards for  

EU/UK Directives

BS EN 61800-3:2004/A1:2012 - Emission kategori C1, Immunitet second 

environment 

BS EN 61800-5-1:2007/A1:2017 - The control unit is intended for installation 

in environments with a pollution rating of 2 (Pollution degree 2)

This declaration of conformity is issued under the full responsibility of the 

manufacturer

   

 

      

  
  

                                                                    

Höganäs 2021-09-01

  

 

  

                                                    

IBC control AB

 

 

   

 

 

   

 

 

     

    

   Christer Persson

     

 

  

                                                    

MD

Содержание MicroMax750

















Отзывы: